《游艇专业英语词汇（T2）.docx》由会员分享，可在线阅读，更多相关《游艇专业英语词汇（T2）.docx（13页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、游艇专业英语词汇(T2) 推力轴承箱 thrust box 推力常数 thrust constant 蝶形螺帽,元宝螺帽 thumb nut 坐板支材(小艇) thwart ship bracing plank 瓷砖工作 tile work 舵柄 tiller 生火报时器 time firing (or stoking) indicator (or device) 时控替续器 time relay 镀锡 tinning 张力脚式钻油台 tlp (= tension leg platform) 吨位甲板 tonnage deck 工具,刀具 tool 低稳度 top heavy 顶桅支索帆 to
2、pmast staysail 扭转振动 torsional vibration 不定期船 tramper 变迁流动 transitional flow 定时开关 time switch 理货员办公室 tally office 二重底外侧腋板 tank side bracket 柜型稳定器 tank type stabilizer 焦油水泥 tar cement 张力脚式平台 tbp (= tethered buoyant platform) 齐柏琪夫氏规则 tchebycheffs rule 遥控系统 telemanipulator system 套筒伸缩管 telescopic pipe 套
3、筒伸缩轴 telescopic shaft 套筒伸缩顶桅 telescopic top mast 显示器,示警器 telltale 试锤 test hammer 理论喉深 theoretical throat 热膨胀 thermal expansion 热力学 thermodynamics 温度液压给水调节器 thermo-hydraulic feed water regulator(or two elements feed water regulator) 三心电缆 three-core cable 三级压缩机 three-stage compressor 节流调速 throttling g
4、overning 推力负荷系数 thrust load coefficient 止推轴环 thrust shaft collar 牵拉角型材 tie angle bar 系杆,牵杆 tie rod (or bar) 定时阀系统 timed valve system 定时器 timer 叶端间隙 tip clearance t 形接头,三通管接 t joint 盥洗室 toilet 梳妆架 toilet rack 吨位 tonnage 减吨开口关闭板 tonnage board 上桅 topgallant mast 顶帽形肋骨 top hat frames 俯仰顶索转动座(吊杆) topping
5、 swivel 俯仰绞机(吊杆) topping winch 手栏杆 top rail 气炬焊接 torch welding 鱼雷母舰 torpedo depot ship 扭矩,转矩 torque 总热熵图 total heat entropy diagram 塔型起重机 tower crane 拖缆钩 towing hook 梁规 trammels 水中升降机 transfer capsule 拉应力 tensile stress 第三应力 tertiary stress 回旋试航 tactical trial 索尾滑车 tail block 油轮,液货船 tank vessel (or
6、tanker) 楔形,推拔 taper 攻螺丝机 tapping machine 螺丝攻扳钳 tap wrench t 型材 t bar 上死点 tdc (= top dead center) 柚木 teak 扭曲试验 twisting test 铝热剂,发热焊接剂 thermit (or thermite) 自动记录温度器 thermograph 热固型 thermosetting type 螺纹切削 thread cutting 容许三舱区浸水船 three-compartment ship 推力减少率 thrust deduction coefficient 系梁 tie beam 舵索
7、 tiller rope 时间延迟,时滞 time lag 表涂层 top coat 上死点 top dead center (tdc) 顶帽型材 top hat section 扭转,扭曲 torsion 拖曳式计程仪 towing log 船模试验槽 towing tank t 形件 t piece 换接开关 transfer switch 变压器 transformer 传动装置,传动齿轮 transmission gear 横肋结构船 transverse framed ship 横向强度 transverse strength 移动门型起重机 travelling gantry 木钉
8、 tree nail 三夹层安全玻璃 triplex safety glass 波状变形 tucking (or corrugation) 涡轮机壳 turbine casing (or cylinder) 塔顶甲板 turret deck 甲板间梯 tween deck ladder 双螺桨船 twin screw vessel 隧道形艉 tunnel stern 热应力 thermal stress 三路开关 three-way switch 艉栏杆 taff rail 兽脂,牛脂 tallow 串行复合(引擎) tandem compound 纵列下水 tandem launching
9、鱼雷柜(潜艇) torpedo tank 卷尺,带 tape 挺杆 tappet rod 回转时间 tat (= turn-around time) 电话浮筒 telephone buoy 望远镜 telescope 伸缩吊柜架 telescopic spreader 套筒伸缩通气管 telescopic vent 温度上升系数 temperature rise coefficient 回火弯曲试验 temper bending test 预热空气 tempered air 张力,拉力 tension 张力控制器 tension control assembly 试片,试件 test piec
10、e t 形头 t head 热疲劳 thermal fatigue 热媒柜送风机 thermofan 调温阀 thermostatic valve 三管轮 third engineer 三副 third officer 桨脚,桨座 thole 三极开关 three-pole switch 偏心距 throw of eccentric 桨手座,艇座,艇中坐板 thwart (or bank) 层 tier 定时阀 timing valve 叶端泄漏(涡轮机) tip leak 叶端漏泄 tip leakage 倾斜装置,倾卸装置 tipper 吨位容积 tonnage capacity 每公分吃
11、水吨数 tons per centimeter immersion 上重船,低稳度船 top heavy vessel (or tender ship) 中桅支索 topmast backstay 上舷侧外板(钢船) topside plating 反鱼雷艇驱逐舰 torpedo boat destroyer 鱼雷发射管 torpedo tube 扭矩扳手 torque wrench 扭力试验机 torsion tester 拖索承梁 towing beam 拖航灯 towing light 拖缆短索 towing pendant 殿缘 trailing edge 训练船,实习船 traini
12、ng ship 不定期轮船 tramp steamer 移动滑车 travelling block 架柱 trestle type column 跳脱试验 tripping test 手动举重机 trolley hoist (or trolley) 热带淡水载重线 tropical fresh water loadline (tf) 真方位 true bearing 剑形艉壳板 tuck plate 鲔延绳钓渔船 tuna clipper 钨钢 tungsten steel 逃生通道 tunnel escape 轴道污水井 tunnel well 涡轮泵 turbine pump 蒸汽涡轮机船
13、 turbine steamer (ts) 紊流运动 turbulent motion 产汽量变化比(锅炉) turn down ratio 回旋圈 turning circle 回旋直径 turning diameter 炮台,多角刀架,六角刀架 turret 二芯电缆 twin core cable 双螺桨船 twin screw ship 前后顺序填角潜弧焊 twin tendem fillet welding (ttf) 扭曲试验 twisting test 两级压缩 two stage compression 直通板列 through strake 切线应力 tangent shea
14、ring stress 换接开关 transfer switch 捻转开关 turn switch 艉轴 tail (or screw, or propeller, or stern) shaft 切线坐标 tangential coordinate 螺丝攻,分接,分接头 tap t 形联接 t connection 拉力断裂试验 tension rupture test 暂定规范 tentative specification 端电压 terminal voltage 试纸 test paper 热效率 thermal efficiency 温度比 thermal ratio 铝热焊接,发热
15、焊接 thermit welding 热电势 thermo emf 热塑性绝缘电缆 thermoplastic insulated cable 螺纹车刀 thread cutter 三路开关 three-way switch 帆前上角帆索 throat halyard 喉厚(焊接) throat thickness 全通腋板,贯通托架 through bracket 连通内龙骨 through plate center keelson 直通板列 through strake 闸流体-连纳德系统 thyrister-leonard system 系杆,牵杆,拉杆 tie bar (or rod)
16、 系板 tie plate 梁层 tier of beams 贮木池 timber pond 最接近点时间 time to closest point of approach (tcpa) 嵌合锻接 tongue (or scarph) weld 齿 tooth 辅助空气压缩机 topping up air compressor 韧化处理 toughening treatment 拖缆桩 towing bitt (or post, or bollard) 拖船 towing boat 拖缆 towing line 拖索,拖缆 tow rope (or line) 描图布 tracing clo
17、th 航迹图 track chart 不定期船 tramp boat (or tramper) 阱,祛水器 trap 移动起重机 travelling crane 趋向显示 trend display 试差法 trial and error method 试船况 trial condition 扳机,触发器 trigger 俯仰角 trim angle 艏俯 trim by bow (or head, or stem) 调平舱口 trimming hatch 三通阀 triple valve 真应变 true strain 绝对风向 true wind direction 斜桁纵帆 trysa
18、il 倒扳开关 tumbler switch 气体遮蔽钨弧焊 tungsten arc inert gas welding (tig) 槽道底盘货柜 tunnel bottom container 涡轮机叶系 turbine blading 六角车床,多角车床 turret lathe 甲板间内衬板 tween deck ceiling 双拼吊柜架(货柜) twin-lift spreader 低稳度船 tender vessel (or crank vessel) 帆前下角索环 tack cringle 尾心轴 tail spindle 俯仰平衡柜(潜艇) trimming tank 油轮,
19、液货船 tanker (or tank) vessel 楔形叶片 tapered blade 整补作业灯 task light 最接近点时间 tcpa (= time to closest point of approach) 传令器,电报机 telegraph 低稳度船 tender vessel (or crank vessel) 接线盘 terminal block 试验载重,试验负荷 test load 试验台 test stand 绝热构造 thermal insulation construction 热应力 thermal stress 热电流 thermoelectric cu
20、rrent 自动记录温度图 thermogram 厚度 thickness 螺纹机 threading machine 三层甲板船 three deck vessel 三岛型船 three island vessel 三通旋塞 three way cock 推力轴承,止推轴承 thrust bearing (or block) 推力轴环 thrust collar (or thrust shaft collar) 推力装置 thruster 推力垫,止推垫 thrust pad 气体遮蔽钨弧焊 tig (= tungsten arc inert gas welding) 运木船 timber
21、carrier 锡焊料 tin solder 吨位标志 tonnage mark 减吨开口 tonnage opening 工具架,刀把 tool holder 工具箱 tool kit 天花板 top ceiling 顶吊装置 top lifting device 中桅箍 topmast band 上舷侧 topside 上油箱,上部柜 top tank 上部用材(木船) top timber 转矩变换器(液力传动装置) torque converter 拖船 towing vessel 拖缆马力 tow rope horsepower 传动效率 transmission efficienc
22、y 发射机,发信器,发报机,发话机 transmitter 横向接头 transverse joint 横向稳度 transverse stability 吊遇车 traveller 阀行程 travel of valve 试航船速 trial speed 三胴船体 trimaran 俯仰船况 trim condition 滑接馈线 trolley wire 热带干舷 tropical freeboard 抽橱式断路器 truck type circuit breaker 涡轮机 turbine 涡轮电力驱动 turbo-electric drive 激紊装置 turbulence stimu
23、lator 松节油 turpentine 甲板间肋骨 tween deck frame 二十呎货柜相当数量 twenty feet equivalent unit (teu) 二船台建造方式 two ship way building system 二段增压机 two-stage supercharger 平头钉孔 tack hole 回旋直径 tactical diameter 洗舱 tank washing (or cleaning) 回火色 temper colour 回火 tempering 榫接头 tenon joint 试验机 testing machine 热电偶温度计 ther
24、mocouple thermometer 热虹吸 thermo-syphon 牛眼圈,缆索嵌环 thimble 摇变度 thixotropic index (or degree of thixotropy) 三轮滑车 three fold block (or treble block) 三相 three phase 三夹板 three ply wood 三股索 three stranded rope 咽喉螺栓 throat bolt 节流式热量计 throttling calorimeter 贯穿螺栓 through bolt 气体遮蔽钨弧焊 tig (= tungsten inert gas
25、 ) welding 大修间隔时间 time between overhaul (tbo) 计时雇船 time charter 铁皮剪刀 tinmans shears 趾裂痕(焊接) toe crack 吨位证书 tonnage certificate 最高升程 top lift 中桅帆桁吊索 topsail lift 扭振记录器 torsiograph 扭矩 torsional moment 总热量 total heat 舰塔 tower 拖力 towing force 拖缆绞机 towing winch (or machine, or engine) 描图纸 tracing paper 训
26、练船 training vessel 传动轴 transmission shaft 横肋系统 transverse frame system 电铃 trembling bell 系留试车 trial at anchor 俯仰,俯仰差 trim 吊运车 trolley 管形吊杆 tubular derrick 回旋能力 turning ability 回旋特性 turning characteristics 盘车装置 turning gear 弯部 turn of bilge 双拖网渔船 two boat trawler 三岛型船 three island vessel 转速记录仪 tachog
27、raph 缀合铆钉,定位铆钉 tack (or quilt) rivet 活塞尾杆 tail rod 串行舵 tandem rudder 撕裂试验 tear test 回火脆性 temper brittleness 模板放样 template loft 临时规则 tentative rule 终点压力 terminal pressure 浮拉式平台 tethered buoyant platform (tbp) 蓄热器 thermal accumulator 三维强度计算 three-dimensional strength calculation 节流操纵 throttle control 节流阀 throttle valve 推力 thrust 推力中心 thrust center 推力减少因子 thrust deduction factor 推力轴 thrust shaft 耐密焊接 tight weld 舵链 tiller chain 装载木材载重线 timber loadline (l) 定时开关 time switch 定时齿轮 timing gear