《DTS3401品牌授权规格书森利威尔电子.pdf》由会员分享，可在线阅读，更多相关《DTS3401品牌授权规格书森利威尔电子.pdf（9页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、1P-Channel 30-V(D-S)MOSFETFEATURESHalogen-free Option AvailableTrenchFET Power MOSFETAPPLICATIONSLoad Switch for Portable DevicesPRODUCT SUMMARY VDS(V)RDS(on)()ID(A)a,bQg(Typ.)-300.088 at VGS=-10 V-2.74.1 nC0.130 at VGS=-4.5 V-2.2 GTO-236(SOT-23)SDTop View231 DTS3401SGDP-Channel MOSFETNotes:a.Surfac
2、e Mounted on 1 x 1 FR4 board.b.t=5 s.c.Maximum under Steady State conditions is 166 C/W.ABSOLUTE MAXIMUM RATINGS TA=25 C,unless otherwise notedParameterSymbolLimitUnitDrain-Source Voltage VDS-30VGate-Source Voltage VGS 20Continuous Drain Current(TJ=150 C)a,bTC=25 CID-3.5ATC=70 C-2.8TA=25 C-2.7a,bTA=
3、70 C-2.2a,bPulsed Drain Current(10 s Pulse Width)IDM-12Continuous Source-Drain Diode Currenta,bTC=25 CIS-1.5TA=25 C-0.91a,bMaximum Power Dissipationa,bTC=25 CPD1.8WTC=70 C1.14TA=25 C1.1a,bTA=70 C0.7a,bOperating Junction and Storage Temperature Range TJ,Tstg-55 to 150CSoldering Recommendations(Peak T
4、emperature)c260THERMAL RESISTANCE RATINGS ParameterSymbol TypicalMaximumUnitMaximum Junction-to-Ambienta,ct 5 sRthJA90115C/WMaximum Junction-to-Foot(Drain)Steady StateRthJF5570RoHSCOMPLIANT DTS34012Notes:a.Pulse test;pulse width 300 s,duty cycle 2%.b.Guaranteed by design,not subject to production te
5、sting.Stresses beyond those listed under“Absolute Maximum Ratings”may cause permanent damage to the device.These are stress ratings only,and functional operationof the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.Expo
6、sure to absolute maximumrating conditions for extended periods may affect device reliability.SPECIFICATIONS TJ=25 C,unless otherwise notedParameterSymbol Test Conditions Min.Typ.Max.UnitStaticDrain-Source Breakdown VoltageVDSVGS=0 V,ID=-250 A-30VVDS Temperature CoefficientVDS/TJ ID=-250 A-32mV/CVGS(
7、th)Temperature CoefficientVGS(th)/TJ 4.5Gate-Source Threshold VoltageVGS(th)VDS=VGS,ID=-250 A-1-3VGate-Source LeakageIGSSVDS=0 V,VGS=20 V-100nAZero Gate Voltage Drain CurrentIDSSVDS=-30 V,VGS=0 V-1AVDS=-30 V,VGS=0 V,TJ=55 C-10On-State Drain CurrentaID(on)VDS 5 V,VGS=-10 V-6ADrain-Source On-State Res
8、istanceaRDS(on)VGS=-10 V,ID=-3.5 A 0.0730.088VGS=-4.5 V,ID=-2.5 A 0.1100.138Forward Transconductanceagfs VDS=-10 V,ID=-3.5 A 7SDynamicbInput CapacitanceCissVDS=-15 V,VGS=0 V,f=1 MHz 340pFOutput CapacitanceCoss67Reverse Transfer CapacitanceCrss 51Total Gate ChargeQgVDS=-15 V,VGS=-4.5 V,ID=-2.5 A 4.16
9、.2nCGate-Source ChargeQgs 1.3Gate-Drain ChargeQgd 1.8Gate ResistanceRgf=1 MHz10Turn-On Delay Timetd(on)VDD=-15 V,RL=15 ID -1 A,VGEN=-4.5 V,Rg=1 4060nsRise Timetr4060Turn-Off Delay Timetd(off)2040Fall Timetf1730Turn-On Delay Timetd(on)VDD=-15 V,RL=15 ID -1 A,VGEN=-10 V,Rg=1 5.510Rise Timetr1325Turn-O
10、ff Delay Timetd(off)1730Fall Timetf7.715Drain-Source Body Diode CharacteristicsContinuous Source-Drain Diode CurrentISTC=25 C-1.5APulse Diode Forward CurrentISM-12Body Diode VoltageVSDIS=-0.75 A,VGS=0 V-0.8-1.2VBody Diode Reverse Recovery TimetrrIF=-2.5 A,dI/dt=100 A/s,TJ=25 C 1730nsBody Diode Rever
11、se Recovery ChargeQrr1120nCReverse Recovery Fall Timeta12nsReverse Recovery Rise Timetb5 DTS34013TYPICAL CHARACTERISTICS 25 C,unless otherwise notedOutput CharacteristicsOn-Resistance vs.Drain Current and Gate VoltageGate Charge0246810120.00.51.01.52.0VDS-Drain-to-Source Voltage(V)-Drain Current(A)I
12、DVGS=10 thru 6 VVGS=4 VVGS=3 VVGS=2 VVGS=5 V0.000.050.100.150.20036912-On-Resistance()RDS(on)ID-Drain Current(A)VGS=4.5 VVGS=10 VID=2.5 A024681002468-Gate-to-Source Voltage(V)Qg-Total Gate Charge(nC)VGSVDS=22.5 VVDS=7.5 VVDS=15 VTransfer CharacteristicsCapacitanceOn-Resistance vs.Junction Temperatur
13、e0.00.51.01.52.01.01.52.02.53.03.54.0VGS-Gate-to-Source Voltage(V)-Drain Current(A)IDTC=25 CTC=125 CTC=-55 C01503004506000612182430CissVDS-Drain-to-Source Voltage(V)C-Capacitance(pF)CossCrss0.60.81.01.21.41.61.8-50-250255075100125150TJ-Junction Temperature(C)(Normalized)-On-ResistanceRDS(on)VGS=10 V
14、VGS=4.5 VID=3.2 A DTS34014TYPICAL CHARACTERISTICS 25 C,unless otherwise notedSource-Drain Diode Forward VoltageThreshold Voltage0.00.30.60.91.21.510VSD-Source-to-Drain Voltage(V)-Source Current(A)IS0.110.01TJ=150 C0.001TJ=-50 CTJ=25 C-0.4-0.20.00.20.40.6-50-250255075100125150ID=250 AVariance(V)VGS(t
15、h)TJ-Temperature(C)ID=1 mAOn-Resistance vs.Gate-to-Source VoltageSingle Pulse Power,Junction-to-Ambient0.00.10.20.30.40246810-On-Resistance()RDS(on)VGS-Gate-to-Source Voltage(V)TJ=25 CTJ=125 CID=3.5 A02468100.010.11101001000Time(s)Power(W)TA=25 CSafe Operating Area,Junction-to-AmbientVDS-Drain-to-So
16、urce Voltage(V)*VGS minimum VGSat which RDS(on)is specified10010.11101000.0110-Drain Current(A)ID0.1TA=25 CSingle Pulse1 s,10 s100 s,DCLimited by RDS(on)*BVDSS Limited10 ms1 ms100 s100 ms DTS3401510-310-2110100010-110-41000.20.1Square Wave Pulse Duration(s)Normalized Effective TransientThermal Imped
17、ance10.10.01Duty Cycle=0.5Single Pulse0.020.05Normalized Thermal Transient Impedance,Junction-to-Foot10-310-201110-110-40.20.1Duty Cycle=0.5Square Wave Pulse Duration(s)Normalized Effective TransientThermal Impedance10.10.010.050.02Single Pulset1t2Notes:PDM1.Duty Cycle,D=2.Per Unit Base=RthJF=70 C/W
18、3.TJM-TA=PDMZthJA(t)t1t24.Surface MountedTHERMAL RATINGS(TA=25 C,unless otherwise noted)Note The characteristics shown in the two graphs-Normalized Transient Thermal Impedance Junction-to-Ambient(25 C)-Normalized Transient Thermal Impedance Junction-to-Foot(25 C)are given for general guidelines only
19、 to enable the user to get a“ball park”indication of part capabilities.The data are extracted from singlepulse transient thermal impedance characteristics which are developed from empirical measurements.The latter is valid for the partmounted on printed circuit board-FR4,size 1 x 1 x 0.062,double si
20、ded with 2 oz.copper,100%on both sides.The part capabilitiescan widely vary depending on actual application parameters and operating conditions.DTS34011SOT-23(TO-236):3-LEADbEE1132See1DA2AA1CSeating Plane0.10 mm0.004CCL1LqGauge PlaneSeating Plane0.25 mmDimMILLIMETERS INCHES Min Max Min Max A0.891.12
21、0.0350.044A10.010.100.00040.004A20.881.020.03460.040b0.350.500.0140.020c0.0850.180.0030.007D2.803.040.1100.120E2.102.640.0830.104E11.201.400.0470.055e0.95 BSC0.0374 Refe11.90 BSC0.0748 RefL0.400.600.0160.024L10.64 Ref0.025 RefS0.50 Ref0.020 Refq3838ECN:S-03946-Rev.K,09-Jul-01DWG:5479Package Informat
22、ion 1A P P L I C A T I O N N O T ERECOMMENDED MINIMUM PADS FOR SOT-230.106(2.692)Recommended Minimum PadsDimensions in Inches/(mm)0.022(0.559)0.049(1.245)0.029(0.724)0.037(0.950)0.053(1.341)0.097(2.459)Return to IndexReturn to IndexApplication Note1DisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DA
23、TA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim any and all liability for any errors,inaccuracies or incomplet
24、eness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product.To the maximum extent permitted by applicable law,D
25、in-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including warranties of fitness for particularpurpose,non-infringemen
26、t and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statements are not binding statementsabout the suitability of produc
27、ts for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datasheets and/or specifications may vary in different application
28、s and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s terms and conditions of purchase,including but not limited t
29、o the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek product could result in personal injury or death.Customers using
30、or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any i
31、ntellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyDin-Tek Intertechnology,Inc.hereby certifies that all its products that are identified as RoHS-Compliant fu
32、lfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8,2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE)-recast,unless otherwise specified as non-compliant.Please not
33、e that some Din-Tek documentation may still make reference to RoHS Directive 2002/95/EC.We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Din-Tek Intertechnology,Inc.hereby certifies that all its products that are identified as Halo
34、gen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards.Please note that some Din-Tek documentation may still make referenceto the IEC 61249-2-21 definition.We confirm that all the products identified as being compliant to IEC 61249-2-21conform to JEDEC JS709A standards.Legal Disclaim
35、er NoticeDisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim an
36、y and all liability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any
37、 product.To the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including
38、 warranties of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statemen
39、ts are not binding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datash
40、eets and/or specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s
41、terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek produ
42、ct could result in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Legal Disclaimer Notice