《基于摩擦传动的高分辨率和大冲程的微量进给机械系统毕业论文外文翻译.doc》由会员分享，可在线阅读，更多相关《基于摩擦传动的高分辨率和大冲程的微量进给机械系统毕业论文外文翻译.doc（16页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、外文资料与中文翻译Micro-feed Mechanism with High-Resolution and Large-StrokeBased on Friction DriveHaitao Liu, Zesheng LuSchool of Mechantronics Engineering, Harbin Institute of TechnologyABSTRACTBased on friction driving principle, design a long stroke length and high resolution walking micro-feeding device
2、 driven by piezoelectric ceramic elements and combined with the screw shaft and aerostatic guide way. The design was made to the adjustable preload device by flexible four-bar linkage. The static properties of flexible linkage device are analyzed with FEM. The transmission characteristics of micro-f
3、eeding device are exhaustively analyzed.Keywords: Friction drive, Piezoelectric actuator, Flexure hinge,Finite element1. INTRODUCTIONAspheric optics has been widely used in industries such as aviation, aerospace, national defense and so on. However, the manufacture of large aspheric optics faces man
4、y problems such as great difficulty, low efficiency, high cost, increased requirement on process equipment etc 1, 2 . In order to arrive at high precision, the micro displacement resolution of ultra-precision machine must be further advanced, so as to compensating the processing error online. Theref
5、ore, the design of micro-feed mechanism has become one of the key technologies 3-7 . PZT is the new micro-feed mechanism developed in recent years. It has the advantages such as small volume, large power, high resolution, and high frequency response and so on and phenomena such as no heating, no bac
6、klash and mucosity, so its widely used micro controller in micro-feed mechanism. Nowadays, friction gearing mechanism is gradually been acquired and used 8, 9.2. STRUCTURE AND OPERATING PRINCIPLE OF MICRO-FEED MECHANISMThe micro-feed mechanism is made up of three parts: friction gearing, ball screw
7、and static-pressure air-bearing guide way. Micro-feed mechanism uses the piezoelectricity ceramic friction gearing block, which twist up the sleeve and drive the ball screw, so as to bring along the air-bearing guide way to realize the micro-feed movement. The structure is shown as Figure 1.1-Bearin
8、g bracket 2-Friction gearing block 3 Friction gearing sleeve 4-Static-pressure air-bearingguide way 5- Ball screw 6- Piezoelectricity ceramic base 7-Piezoelectricity ceramic used for feeding Figure 1: (a) Structure of the feed mechanismAs shown in Figure 2, the operating principle of the feed mechan
9、ism is that, friction gearing sleeve connects with ball screw, four friction gearing blocks are placed symmetrically at both sides of the sleeve. Each block is droved by the corresponding piezoelectricity ceramic used for feeding and is gripped by the corresponding gripping mechanism, which is drove
10、d by the piezoelectricity ceramic used for gripping to produce clamp force. When feeding mechanism works, the piezoelectricity ceramic used for gripping on the same side drive both the friction gearing blocks to work in certain orderliness, so as that the friction gearing sleeve turn continuously.Fi
11、gure 1: (b) Picture of the feed mechanismFigure 2: Operating principle of the feeding mechanism3. DESIGN OF THE ADJUSTABLE PRETIGHTENING MECHANISMAn adjustable retightening mechanism is required in the friction gearing mechanism, which must has enough pretightening force. The typical pretightening m
12、ethods are plate spring pretightening mechanism, helical pretightening mechanism, and air pressure pretightening mechanism and so on. The retightening mechanism designed in this paper is flexible parallel four bars mechanism. Its droved by piezoelectricity ceramic to supply pretightening force. The
13、pretightening force can be changed by controlling the input voltage of piezoelectricity ceramic.As shown in Figure 3, use the finite element software to analysis the static characteristic. When the drive force of piezoelectricity ceramic is 500N in maximum, the rigidity of flexible four bars mechani
14、sm, analyzed by finite element software, is K=24. 1 5N/m, and the maximum stress of flexible hinges is =32.7Mpa. If there is no distortion in flexible four bars mechanism (that is when the friction gearing blocks contact rigidly), the output force of piezoelectricity ceramic will completely translat
15、es to pretightening force through the flexible four bars mechanism.4. DRIVE CHARACTERISTIC ANALYSIS OF THE MECHANISMStudying and mastering the drive characteristic of mechanism redounds to adopting the proper measures to improve the whole performance and provides the design basis for designing the c
16、ontrol system.4.1 Drive torqueWhen system starts, there is a problem on initial inertia moment as a result of the existence of parts quality. To research the drive torque, choose the friction gearing sleeve as subject investigated. According to the theory that the kinetic energy of gearing train is
17、same before and after conversion, the rotary inertia of each part is transformed to friction sleeve. Because of that, we can get the rotary inertia after conversion is(a) Structure of the pretightening mechanism(b) Node motion nephogram(c) Von-mise stress envelopeFigure 3: The static characteristic
18、assay plan of pretightening mechanismWhere p is pitch of lead screw, m;r is radius of the friction sleeve, m; mS is quality of the ball screw, kg;T is quality of the friction sleeve, kg.Through the above analysis, we get the equivalent rotary inertia of friction sleeve. Now we choose the friction sl
19、eeve as subject investigated to discuss the drive torque （ drive force） that is needed when device starts and its influencing factors. The following equation works when device starts:Where J is equivalent rotary inertia, kgm2; is angular acceleration of friction sleeve, rad/s2;r is radius of the fri
20、ction sleeve, m;M is drive torque, Nm; F is drive force （breakout friction between friction block and friction sleeve） , N.When system starts, a condign drive deflecting couple should be applied on the friction sleeve, in order that the sleeve can have certain angular acceleration. The drive deflect
21、ing couple is generated by the output force of piezoelectricity ceramic. From equation 2 we can get that the equivalent rotary inertia of system, radius of the friction sleeve and drive force of the piezoelectricity ceramic (breakout friction between friction block and friction sleeve) are the influ
22、encing factor of mechanism start, so we should think over the influence of each factor to ensure the normal start of mechanism. Same questions exist when feed mechanism stop moving.4.2 Driving rigidityThe driving rigidity is one of the important driving characteristics of feed mechanism. Now we will
23、 analyze the driving rigidity of feed mechanism in detail as following.The rigidity of the feed mechanism is the cascade connection of the each segment rigidity of the feed mechanism, which has the calculated equation as follows:Where K is the total rigidity of the feed mechanism; KF is the touching
24、 rigidity of surface in contact between friction block and friction sleeve;KS is the axial rigidity of lead screw;KS is the axial rigidity changed from the torsional rigidity of lead screw;KN is the rigidity of nut;KB is the rigidity of axial bearing;KH is rigidity of nut bracket and bearing block;K
25、D is the axial rigidity of nut link block; Here is the analysis and calculation of part rigidity.4.2.1 Rigidity of the piezoelectricity ceramicThe piezoelectricity ceramic in this paper is the ceramic micro positioner typed WTYD0808055 produced by China Electronics Technology Group Corporation No.26
26、 Research Institute. Its rigidity measured through experiment is 15.1 5N/m, as shown in Figure 4.4.2.2 Touching rigidity of surface in contact between friction block and friction sleeveTwo objects contacting with each other will have certain tangential transition before relative slip in the action o
27、f tangential external force, which is called pre-displacement. The proportional relation between force and displacement reflects a rigidity characteristic in fact 10. The corresponding rigidity now is:Where k is const;N is normal pressure;r is the radius of idealized sphere on friction surface.Its c
28、lear in the equation that, in special friction gearing system, k is got from experiment, r is const, the only influencing factor of touching rigidity is normal pressure N. Its evident that the larger N is, the larger the touching rigidity K is.Figure 4: Rigidity curve of piezoelectricity ceramic4.2.
29、3 Axial rigidity changed from the torsional rigidity of lead screwThe dimension of driving chain needs to be transformed uniformly when calculating its rigidity. Therefore, the torsional rigidity must be transformed into axial rigidity as the following equation:Where a is the rising angle of lead sc
30、rew, ();d is the diameter of lead screw, mm;F is the axial force of lead screw, N;M is the input moment of lead screw, Nmm;q is the friction angle between lead screw and nut, ();KT is the torsional rigidity of lead screw, Nmm/rad;0 is the torsional deformation of lead screw, rad;p is the lead of lea
31、d screw, mm;G is the shear modulus of elasticity of lead screw material, Mpa;JP is the inertia moment of cross section, mm4, JP=d4/32;L is the maximum distance from loading point to two thrust bearing, mm.The axial rigidity of nut link block can be gained by the finite element analysis. The rigidity
32、 of nut bracket and bearingblock is very large, which can be dismissed. The rigidity of other parts can be got by looking up table and calculating.In a word, by deducing the equation of drive rigidity of feed mechanism, we have found the influencing factors ofdriving rigidity caused by each driving
33、segment, which offers the basis for further study on the driving characteristic.5. EXPERIMENTAL STUDY OF THE FEED MECHANISM 5.1 Foundation of the experiment systemAs shown in Figure 5, the experiment system is made up of feed mechanism, computer, piezoelectricity ceramic driver and its power supply
34、and the inductance amesdial.Figure 5: Foundation of experiment systemThis paper uses a control method based on average curve model to set up the open loop control model. Above all, measure the experimental curve of relation between piezoelectricity ceramic control voltage and slide carriage distance
35、. Using the Matlab software to fit the line with cubic algebraic multinomial, and the fitted line and fitted error line are as shown in Figure 6, from which we get the corresponding relational expression of control voltage and distance and therefore control the distance of feed mechanism. a) Fitted
36、line b) Fitted error lineFigure 6: Fit with cubic algebraic multinomialRelational expression of control voltage and distance is as shown in equation 7:Where x is the output distance, m;u is the control voltage, V.5.2 Experimental study of system resolutionAs shown in Figure 7, piezoelectricity ceram
37、ic has certain elongation. At this time, the distance of micro working table is 0.1 5m. Then step elongating gradually on this base and keep 1.5s in each moment. The sampling time is 100ms. The resolution curve can be gained by measuring the practice distance of micro feed mechanism using the induct
38、ance amesdial.Figure 7: Distance resolution curve of feed mechanism6. CONCLUSIONA step micro feed mechanism with long march and high resolution was designed in this paper, and the following conclusions were concluded:1. Designed the pretightening mechanism based on the piezoelectricity ceramic flexi
39、ble iron hinges and analyzed its static characteristic using the finite element software;2. Analyzed the starting torque of micro feed mechanism and calculated the equivalent rotary inertia; analyzed the driving rigidity characteristic of micro feed mechanism and found its influencing factors;3. The
40、 march of the micro feed mechanism can reach 300mm, and the resolution is less than 0.05m.REFERENCES1. Seugng-Bok Choi, Sang-Soo Han. Position Control System Using ER Clutch and Piezoactuator. Pro. of SPIE, 2003, 5056: 4244312. Suzuki H, Kodera S, Mabkawa S, et al. Study on Precision Grinding of Mic
41、ro a Spherical Surface. JSPE, 1998, 64(4):61 9623.1. Arrasmith S. R, Kozhinova I A, Gregg L L et al. Details of The polishing Spot in Magnetorheological Finishing(MRF).Proceedings of SPIE-the International Society for Optical Engineering,2001 ,Vol.3782:92100.2. Atherton P D, Xu Y, McConnell M. New X
42、-Y Stage for Precision Positioning and Scanning. SPIE, 1996, 2865:1 520.3. Liu Yung -Tien, Toshiro Higuchi, Fung Rong-Fong. A Novel Precision Positioning Table Utilizing Impact Force of Spring-Mounted Piezoelectric Actuator. Precision Engineering, 2003, 27:142214. Lobontiu N, Goldfarb M, Garcia E. A
43、 Piezoelectric Drive Inchworm Locomotion Device. Mechanism and Machine Theory, 2001, 36: 425443.5. A. A. Elmustafa, Max G. Lagally. Flexural-hinge Guided Motion Nanopositioner Stage for Precision Machining: Finite Element Simulations. Precision Engineering, 2001, 25: 778 16. Jaehwa Jeong, Young-Man
44、Choi, Jun-Hee Lee. Design and Control of Dual Servo Actuator for Near Field Optical Recording System. Pro. of SPIE, 2005, 6048: 187. Kim Jeong-Du, Nam Soo-Ryong. Development of a Micro-depth Control System for an Ultra-precision Lathe Using a Piezoelectric Actuator. International Journal of Machine
45、Tools and Manufacture. Volume:37,Issue:4, April, 1997, pp.4955098. Li Sheng-yi, Luo Bing, Dai Yi-fan, Peng Li. Design and Experiment of The Ultra Precision Twist-roller Friction Drive. ICAMT99. 1999.基于摩擦传动的高分辨率和大冲程的微量进给机械系统哈尔滨工业大学机电工程学院刘海涛，卢泽生摘 要 在摩擦传动原理的基础上,设计了一种通过压电陶瓷结合螺杆轴和气体静压引导的方式驱动的长冲程和高分辨率的微量进
46、给系统。设计用来使加载装置可以灵活的起落。利用有限元方法对柔性连接装置对它的静态特性进行分析。对这种微量进给系统的传输特性进行了详细的分析。关键词： 摩擦传动 压电传动装置 柔性铰链 有限元1.简介光学在航空、航天、国防等领域中已得到广泛应用的行业。然而,生产的大型光学镜面面临着巨大的困难,效率较低、成本较高、增加在工艺设备的要求等。为了获得更高的精度，高微位移分辨率超-先进精密机床有待进一步深入,以补偿加工误差。因此,微量进给机制的设计已成为其关键技术之一。压电陶瓷是一种近年来发展起来的新型的微量进给机制。它所拥有的优势,比如体积小、功率大、分辨率高和高频率响应,恒温,不反弹，无粘性。因此它
47、广泛使用在微量进给机制。如今,摩擦传动机制逐步被获得和使用。2微量进给机制的结构和工作原理微量进给机制是由三个部分组成:摩擦传动装置、滚珠螺杆及静态压力空气轴承引导的方式。采用压电陶瓷微量进给机制阻滞,这些摩擦传动扭曲向上套筒和驱动器滚珠丝杠,从而带动空气轴承引导地实现了微量进给运动。 结构如图1所示。1， 轴承支架，2.活塞，3、活塞缸，4.精压力空气轴承导轨，5.滚珠丝杠，6. 压电陶瓷底座，7.压电陶瓷底座图一：进给机构的结构按照图2所示的进给系统工作原理是,套筒连接着球摩擦传动螺杆、四个模块是放置的两侧对称的轴套。每一块由相应的压电陶瓷用于驱动,这种机制由于是由压电陶瓷驱动，适用于夹持
48、产生夹力。进给机制的运作,压电陶瓷适用于夹持在同一阵营的摩擦传动驱动都工作在特定块整齐,从而使摩擦传动套筒连续的传动。图1:(b)进给系统图片图2:进料机构的运行原理3结合设计的可调机制 拧紧调节机制是一个需要在摩擦传动机构，它必须有足够的 预紧力。典型的方法是钢板弹簧预紧预紧机制，螺旋预紧 机制，气压预紧机制等。该拧紧机制本文设计的 灵活的平行四杆机构。这是由压电陶瓷droved供应预紧力。该 预紧力可以改变控制的压电陶瓷输入电压。 如图3所示，利用有限元软件分析的静态特性。当驱动力的 压电陶瓷是在最大500N的，灵活安排四杆机构刚度，有限元分析 软件，是K =24.15N/m，以及最大应力弹性铰链是= 32.7Mpa。如果没有灵活失真 四杆机构（即当摩擦传动板块跟硬性），输出力的压电 陶瓷将完全转化为预紧通过灵活的四杆机构的力量。4驱动特性分析的机制学习和掌握辐射源驱动特性的机制以便采取适当的措施，以改善整体性能，并提供了设计控制系统设计的基础。4.1驱动力矩当系统启动时，有一个初步的转动惯量作为零件的质量存在问题的结果。为了研究驱动力矩，选择摩擦传动套筒为主体的影响。根据该理论认为，动力学传动