《测量工具中英文对照表大全(共7页).doc》由会员分享，可在线阅读，更多相关《测量工具中英文对照表大全(共7页).doc（7页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、精选优质文档-倾情为你奉上测量工具中英文对照表大全测量工具中英文对照表heodolite 经纬仪Water Level 水位仪Level Ruler 水平尺Casing gradienterCoating thickness Measurer 涂层测厚仪Ultrasonic thickness measurer 超声波测厚仪Ultrasonic crack detector 超声波裂纹测试仪Digital thermometer 数字温度计radiation thermometer 辐射温度计Gradient Reader 坡度读数器Volometer 万用表MegaOhmmeter 兆欧表E
2、arthing resistance Reader 接地电阻读数表Plug gauge 圆柱塞规Magnifying glass 放大镜Plummet 铅锤Profile projector 投影仪Pin Gauge 针规(不知道和plug gauge 的区别在哪里,知道的请指正)Gauge block 块规Bore gauge 百分表A vernier caliper 游标卡尺Coordinate Measureing Machine(CMM) 三尺元Pressure gague寸压力计电度厚度测试仪(Electroplating THK.Tester)转(扭)力仪(Twisting Met
3、er)螺纹规(Thread Gauge)块规(Block Gauge)环规(Ring Gauge)力矩计(Torque Meter)塞规(Plug gage)高度仪(Altitude gauge)塞尺/间隙规(Clearance gauge)千分卡尺(Micrometer Calipers )“过” - “不过” 验规(通-止规) go-no-go gauge游标卡尺(Vernier Caliper)电子卡尺(Digital caliper)深度千分尺(Depth Micrometer)销(针)规(Pin Gauge)投影仪(Projector )数字高度测量仪(Digital Height
4、Gauge)表面处理测试仪(Surface Finish Tester)内/外径千分尺(Inside/outer Micrometer)洛(威)氏硬度仪(HRC/HV) Hardness Tester)温度计(Thermometer)孔规(Bore Gauge)电子称(Electric/digital Balance)三坐标测试仪 (CMM)万用表(Multimeter)1.刀口型直尺:knife straigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht e
5、dge5.条式和框式水平仪bar form and square levels6.合像水平仪 imaging level meter7铸铁平板 cast iron surface plate8.岩石平板 granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪 roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面 roughness comparison
6、 specimens cast surface14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparison specimens-ground,turned,bored,milled,shape and planed15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machining surfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.
7、轨迹轮廓 traced profile20.基准轮廓 reference profile21.总轮廓 total profile22.原始轮廓 primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storing stylus instrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器dri
8、ve unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profile filtering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument41.静测力的变
9、化change of static measuring force42.静态测力 static measuring force43.动态测量力 dynamic measuring force44.滞后hysteresis45.测头的测量范围 transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力 instrument resolution49.量程分辨力比range-to-resolut
10、ion ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输 vertical profile component transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blasted surfaces54产品结构几何量计术规范（GPS）geometrical product specifications(GPS)55表面结构 surface texture
11、56接触式仪器的标称特性 nominal characteristics of contact instruments57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差 maximum permissible error59圆柱直齿渐开线花键量规 gauges for straight cylindrical involute splines60齿厚游标卡尺 Gear tooth verniercalipers61齿轮渐开线样板the involute master of gear62齿轮螺
12、旋线样板 the helix master of gear63矩形花键量规 gauges for straight sided splines64测量蜗杆 master worm65万能测齿仪 universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机 Universal gear measuring machine69齿轮螺旋线测量仪gear helix measur
13、ing instrument70便携式齿轮齿距测量仪 manual gear circular pitch measuring instrument71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuring instrument75
14、梯形螺纹量规 gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸 Types and dimensions of metric trapezoidal screw threads79.普通螺纹量规型式与尺寸 Types and dimensions of gauges purpose screw thread
15、s80.非螺纹密封的管螺纹量规 Gauges for pipe threads prcessure-tight joints are not made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差 maximum permissible error83.间隙螺纹量规 Clearance screw gauge84.量针Bar gauge85.螺纹样板 Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are
16、made on the threads87.刀具预调测量仪? 精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.
17、量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator一般术语：1.几何量 geometrical product2.量值value(of a quantity)3.真值true value(of a quantity)4.约定真值 conventional true value(of a quantity)5.单位unit(of measurement)6.测量measurement
18、7.测试measurement and test8.检验inspecte9.静态测量static measurement10.动态测量dynamic measurement11.测量原理principle of measurement12.测量方法method of measurement13.测量程序measurement procedure14.被测量measurand15.影响量influence quantity16.变换值transformed value(of a measurand)17.测量信号measurement signal18.直接测量法direct method of
19、 measurement19.间接测量法indirect method of measurement20.定义测量法definitive method of measurement21.直接比较测量法direct-comparison method of measurement22.替代测量法substitution method of measurement23.微差测量法differential method of measurement24.零位测量法nulll method of measurement25.测量结果result of a measurement26.测得值measur
20、ed value27.实际值actual value28.未修正结果uncorrected result （of a measurement）29.已修正结果corrected result(of a measurement)30.测量的准确度accuracy of measurement31.测量的重复性repeatability of measurement32.测量复现性reproducibility of measurements33.实验标准偏差experimental standard deviation34.测量不确定度uncertainty of measurement35.测
21、量绝对误差 absolute error of measurement36.相对误差 relative error37.随机误差random error38.系统误差 systematic error39.修正值correction40.修正系数correction factor41.人员误差personal error42.环境误差environmental error43.方法误差error of method44.调整误差adjustment error45.读数误差reading error46.视差parallax error47.估读误差 interpolation error48
22、.粗大误差parasitic error49.检定verification50.校准calibration51.调准gauging52.调整adjustment几何量测量器具术语1.几何量具测量器具dimensional measuring instruments2.长度测量器具length measuring instruments3.角度测量器具angle measuring instruments4.坐标测量机coordinate measuring machine5.形状和位置误差测量器具form and position error measuring instruments6.表面
23、质量测量器具surface quality measuring instruments7.齿轮测量器具gear measuring instruments8.实物量具（简称“量具”）material measure9.测量仪器（简称“量仪”）measuring instruments10.测量链measuring chain11.测量装置measuring system12.指示式测量仪器indicating(measuring )instrument13.记录式测量仪器recording（measuring）instrument14.累计式测量仪器totalizing(measuring)i
24、nstrument15.积分式测量仪器integrating(measuring)instrument16.模拟式测量仪器analogue(measuring)instrument17.数字式测量仪器digital(measuring)instrument18.测量变换器measuring transducer19.传感器sensor20.指示装置indicating device21.记录装置recording device22.记录载体recording medium23.标尺标记scale mark24.指示器index25.标尺scale26.度盘dail测量器具术语1.标称值nomi
25、nal value2.示值indication(of a measuring instrument)3.标尺范围scale range4.标称范围nominal range5.标尺长度scale length6.标尺分度scale division7.分度值value of a scale division8.标尺间距scale spacing9.线性标尺linear scale10.非线性标尺non-linear scale11.标尺标数scale numbering12.测量仪器的零位zero of a measuring instrument13.量程span14.测量范围measuri
26、ng range15.额定工作条件vated operating conditions16.极限条件reference condition17.标准条件reference condition18.仪器常数instrument constant19.响应特性response characteristic20.灵敏度senstivity21.鉴别力discrimination22.分辨力resolution（of an indicating device）23.死区dead band24.准确度accuracy of a measuring instruments25.准确度等级accuracy
27、class26.重复性repeatability of a measuring instrument27.示值变动性varation of indication28.稳定度stability29.可靠性reliability30.回程hysteresis31.漂移drift32.响应时间response time33.测量力（简称“测力”）measuring force测量器具术语1.实物量具示值误差error of indication of a material measure2.测量仪器示值误差error of indication of a measuring instrument3.
28、重复性误差repeatability error of a measuring instrument4.回程误差hysteresis error5.测量力变化variation of measuring force6.测量力落差hysteresis of measuring force7.偏移误差bias error (of a measuring instrument)8.允许误差maximum permissible errors(of measuring instruments)9.跟踪误差tracking error (of a measuring instrument)10.响应率误
29、差response-law error (of a measuring instrument)11.量化误差quantization error (of a measuring instrument)12.基值误差datum error (of a measuring instrument)13.零值误差zero error (of a measuring instrument)14.影响误差influence error15.引用误差fiducial error16.位置误差position error17.线性误差linear error18.响应特性曲线response characte
30、ristic curve19.误差曲线error curve20.校准曲线calibration curve21.修正曲线correction curve长度测量器具量具类1.量块gauge block2.光滑极限量规plain limit gauge3.塞规plug gauge4.环规ring gauge卡规snap gauge5.塞尺feeler gauge6.钢直尺steel gauge7.精密玻璃线纹尺precision glass linear scale8.精密金属线纹尺precision metal linear scale9.半径样板radius template卡尺类1.游标
31、卡尺vernier caliper2.带表卡尺dial caliper3.电子数显卡尺calliper with electronic digital display4.深度标游卡尺depth vernier caliper5.电子数显深度卡尺depth caliper with electronic digital display6.带表高度卡尺dial height calliper7.高度游标卡尺height vernier caliper8.电子数显高度卡尺height caliper with electronic digital display9.焊接检验尺calliper for
32、 welding inspection千分尺类1.测微头micrometer head2.外径千分尺external micrometer3.杠杆千分尺micrometer with dial comparator4.带计数器千分尺micrometer with counter5.电子数显外径千分尺micrometer with electronic digital display6.小测头千分尺small anvil micrometer7.尖头千分尺point micrometer8.板厚千分尺sheet metal micrometer9.壁厚千分尺tube micrometer10.叶
33、片千分尺blade micrometer11.奇数沟千分尺odd fluted micrometer12.深度千分尺depth micrometer13.内径千分尺internal micrometer14.单杆式内径千分尺single-body internal micrometer15.表式内径千分尺 dail internal micrometer16.三爪式内径千分尺three point internal micrometer17.电子数显三爪式内径千分尺three point internal micrometer18.内测千分尺inside micrometer指示表类1.指示表
34、 dial indicator2.深度指示表depth dial indicator3.杠杆指示表dial test indicator4.内径指示表bore dial indicator5.涨弹簧式指示表 expanding head bore dial indicator6.钢球式内径指示表ball type bore dial indicator7.电子数显指示表dial indicator with electronic digital display8.杠杆卡规indicating snap gauge9.带表卡规dial snap gauge10.带表外卡规outside dial
35、 snap gauge11.带表内卡规inside dial snap gauge12.测厚规thickness gauge13.扭簧比较仪microcator14.杠杆齿轮比较仪mechanical dial comparator15.电子量规electronic gauge16.电感式传感器inductance type transducer17.指示装置indicating device18.电感测微仪inductance micrometer19.峰值电感测微仪peak inductance micrometer20.电感内径比较仪inductance bore comparator21.瞄准传感器aiming transducer专心-专注-专业