《LED显示屏中英文手册.docx》由会员分享，可在线阅读，更多相关《LED显示屏中英文手册.docx（17页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、LED 电子显示屏用户手册LED electron display handbook for consumerLED 电子显示屏硬件局部LED electron display hardware part LED 电子显示屏保修证书LED electron display warranty certificate警告Warning警告:为了防止任何身体上的损害,请在连接开关之前,读这个安装操作规章Warning:To protect any body damage ,please install the instruction before you connect the switch.1 在
2、翻开开关前，检查全部的沟通电源是不是连接好。Before you open the switch .please check if all the alternating current power were connected correct.2 在做任何维护工作之前要先关掉包括LED 板电脑终端系统盒和监控器在内的全部开关.Please close the switch of LED board ,the computer terminal system box and monitor ,before you do any maintenance.3 在开关未关闭时，不要触电源。When
3、you open the switch ,don”t touch the power .警告：为了安装设备驱动程序的损失和数据的丧失，请在操作显示板之前读这个安装设置操作规章。Warning: To avoid the damage of the driver and the data disappear ,please read the operation rule of the installation device before you operate with the led.1 在连接任何电缆之前，请先关掉包括LED 板电脑终端系统盒和监控器在内的全部开关。Before you co
4、nnect any signal cable ,Please close all the switch of LED display ,computer terminal ,system box and monitor first.2 在更换电子器件之前请在手上带好抗静电环！Befor you changethe electric parts please put on the anlistatig loop . 3.在更换模块前，请在模块和连接面板上钩一个安全的绳索Befor you change the module ,please knot a safe cord between the
5、 module and the panel of the module.LED 电子显示屏使用流程说明The instruction of the lED display为保证我们的产品可以在合理的条件下正常使用，得到您对产品的认可，我们将简述产品的使用流程以及留意事项，请认真阅读后，再进展LED 显示屏的安装和调试工作.To guarantee our products can be used in the normal condition, we now make a brief introductionOf products use technological process and a
6、ttention information .Please read it carefully and then proceed with the installation and debugging.1 使用硬件设备清单List of the hardware equipmentLED 显示屏 信号连接线 电源连接线 系统掌握卡装载在电脑内 系统接收卡转载在LED 电子显示屏内台式电脑含DVI 视频输出及串口 显示屏以及相关附属配件。LED display Signal cable Power connection line Control system cards (installed in
7、 the PC) Receiving cards of system(installed in the LED display) PC (include the DVI videlo output and the com)LED display and the concerned fittings .2 使用流程The use flow 硬件安装Installation of the hardware安装步骤如下：The step of installation as fallows:1把 DVI 显示卡插于主板的AGP 插槽，安装好该卡的驱动程序；Insert the DVI display
8、 cards in the APG com of the main board and install the driver program of the cards . 2将数据采集拉插与空的PCI 插槽假设有使用；If there is one sending cards ,please insert it in the vacant PCI com .3用 DVI 电缆线把数据采集卡与显示卡连接在一起；Connect the data collection cards and display cards with the DVI cable . 4把掌握线与串口Rs232相连可选，灵星雨
9、系统需要； Connect the control line with the com (Rs232) just for linsn system) .5用网线与接收卡相连；具体条数依据工程图纸；Connect the receiving cards with the signal cable.(the number of strip is according to the blueprint) 6检查连接无误即可进展设置或上电调试。If there is no mistakes ,you can install it or debug it .软件安装Iistallation of the
10、sofeware安装步骤如下：The Installation processas follows:1显卡驱动安装 Install the display driver将显卡驱动程序光盘插入光驱，即可自动进入安装状态，请按提示操作即可。Insert the display driver CD in the CD ROM , it could come into the installstate automatismly then just follow the clew.首先安装DirectX8.0；然后安装掌握版面。First ,install the Direct X8.0, then i
11、nstall the control panel . 2播放软件Play software安装大屏幕专用播放与设置软件LED 演播室，或其他掌握软件Install the special display and setting software of the LED studio or other control software .将随屏所附应用软件光碟插入光驱，复制或安装全部的程序到计算机上。Insert the attached software CD in the CD-ROM ,copy or install all the process to PC .3 电子屏操作步骤(重要)p
12、rocess of manipulation of the display .1开屏：请先翻开计算机，再翻开电子屏。Light the led display :please open the PC first and then open the LED display .为各设备通入电源确保输入电压符合产品要求Supply the equipment with electric power .(make sure import the open voltage)翻开 LED 屏体屏体通电瞬间会有区域性的闪耀，说明屏体通电，翻开计算机，务必确保显卡设置正确不正确会没有显示画面，叫黑屏，翻开掌握
13、软件，进展根本的像素尺寸和显示区域设置此设置并不影响LED 显示屏画面的显示Open the LED display (there will be a flicker at moment ,indicating there is power in the LED display ),start the PC and make sure the display cards are correctly set (if it were wrongly set ,there will no pictures .Just black screen),open the control software ,
14、proceed with the dimension of the basal picture elements and the place of the display,(this setting didnt influent the pictures of LED display).2关屏：首先关掉LED 屏体电源，关掉掌握软件，再正确地关闭计算机。Close the LED display :first close the power of the LEDdisplay ,close the control sofeware ,then close the PC .4觉察问题Questi
15、on1 检查各连接方式是否正确，包括强电局部的连接弱电局部已经在生产企业测试完成，信号连接是否正确，主要为系统接收卡输入与输出方向是否正确，接收卡上有方向示意。系统连接是否正确请翻阅系统连接说明Please check if the connection method is right ,include the hige power voltage (the low power voltage have already test well ),the signal cable whether connected correct .There is guidance at the receivi
16、ng cards .The system connect correctly .(Please read the instruction of system connection .)2 计算机软件局部是否完成安装，包括显卡的设置请翻阅显卡设置说明和掌握软件安装。Check if the software of the PC installed well ,including the setting of display cards(please read the instruction )and installation of control software .5留意事项Attention
17、1遵守用户使用守册中的操作步骤：Follow the manipulation steps of .2防潮，湿度要求为：最高工作温度时，LED 显示屏应小于相对湿度为 92 Moisture proof ,the humidity standard is below the relative humidity of 92LED display atthe tiptop temperature .3温度适当，温度要求为：工作环境温度-20Ct40CThe proper temperature ,the working circumstance temperature -20Ct40C 储存环境温
18、度-40Ct60CDeposited temperature -40Ct60C 4供电电源要符合要求The proper supply powerLED 显示屏的供电电源电压：220V10 频率：50HZ5The supply power voltage of the LED display :220V10 HZ: 50HZ5 安全大地接触牢靠，地线与零线隔离牢靠，接入电源远离大功率用电设备。The connection terra line and cipher line were insulated .when supply the power please keep away from
19、the high-power equipment .*非专业人士请勿翻开修理。Lay people do not open and mend the LED display .在操作流程中的其他问题，请翻阅我们相关的说明，如再有疑问请联系我们。If any questions please read the concerned instructio,nIf you need anyhelp please contact us .以上考虑还有不全面的地方以后在使用过程中再补充，也期望您能够多提建议，共同维护和使用好显示屏。There maybe pretermission in the inst
20、ruction ,we will renew it in future .wehope you can make suggestions fo us,maintenance together and correct use the diaplay.LED 显示屏常见的故障及其排解方法The malfunction and resolution method of LED display1. 整屏不亮黑屏The whole screen cannot be enlightened.(black screen)1.1 :检查屏体的供电状况，用试电笔或万用表检测开关连接用电器端是否有电。开关可能消灭
21、问题， 或者短线。Check the power supply of the display.Use the test pencil or the multimeter to check if there is power at the electric end of the switch.There maybe something wrong with the switch or circuit.1.2 :对于与计算机同步的显示屏，首先检查计算机是否进入休眠状态或者进入屏幕保护状态；假设进 入休眠，先进入“掌握面板”，点击“电源治理”，将“系统等待”和“关闭监视器”选项选择“从不”选项，这样
22、计算机不会休眠，显示屏可以正常工作；假设没进入休眠，可以翻开机箱查看掌握卡和通讯电缆是否插接牢靠，检查通讯电缆是否有断线。根本解决上述问题。As for the led display in-phase with PC,first check if the PC were turn into dormancy station or the screen protection station.If it were in the dormancy station,then enter into the “control panel“,start the“ power management“,cho
23、ose “never“ about the “system wait“ and“ close monitor“,then the computer won”t in the dormancy station and the led display will work normally.If the computer didnt enter intodormancy station,then you can open the outline boarder of the computer to make sure that the control card and the signal cabl
24、e whether inserted firmly.Check if the signal cable is break off.After all these can solve the above question.1.3 检测通讯线是否接通，有无接错。同步屏，请依据连接图进展连接并做检查。Check if the signal cabel is go through, if there is no problem .(synchronization screen),please follow the connect print and check-up.1. 整块单元板不亮黑屏The w
25、hole PCB cannot be enlightened.(black screen)2.1 、 连续几块板横方向不亮，检查正常单元板与特别单元板之间的排线连接是否接通。Several of PCB in across cannot be enlightened,check if the line between normal PCB and the abnormal PCB were go through.2.2 、 连续几块板纵方向不亮，检查此列电源供电是否正常。Several of PCB invertical cannot be enlightened,check if the p
26、ower were supply normally.2. 显示文件不全或位置不对The display document cannot show the whole picture or the location is incorrect.3.1 :首先检查软件中的“显示位置”和“屏体大小”的参数与安装工程师给的是否全都，如不记得， 可以到屏体上记数一下长和宽的象素点数，“屏体大小”确定后，可以到屏体上看显示的区域相差多少，然后回到计算机处再进展调整，直到位置吻合为止。First,check if the parameter of the software about the “display
27、 position “and the “size of the led display“ were in accordance with the installation engineer s.If you did nt remember it, you can count the pixel dot of LED display to confirm the size.Then you compare the size with the vision place.Then adjust the settingat the computer,until the vision is all th
28、e same with the LED display.3.2 :假设显示不全面检查所做的文件大小是否与屏体的“屏体大小”全都。If the vision is not all-sided as the size of document,then you check it with the size of LED display. 3.3:翻开机箱检查掌握卡上是否落上导电体。Open the outline border,check if there is conductor at the controlling card.3. 通讯显示屏通讯不上：The led display didnt
29、have the signal.4.1：检查软件中的参数是否与安装工程师给的全都。Check if the parameter of the software is according to the installation engineers. 4.2:检查串口是否接牢，通讯线是否有断线的地方。Check if the com were inserted firmly,the signal cablewhether break off.4. 显示屏抖动，有横条The led display were tingle and appear cross band.检查连接计算机的共地线是否松动，或
30、通讯电缆是否松动。假设操作人员不能推断问题的缘由，或对计 算机不是很了解，不要轻易拆开机箱；或者显示屏的问题很严峻，请准时与我公司联系，经我公司有关人员同意和指示再进展诊断。Check if the terra line connected with the computer is become flexible.If the operator cannot judgethe reason ofthe problem,Or not familiar with the computer, not disconnect the conputer.If there is many questions
31、 of display,please connect our company in time.We will give you some direction then continue with the maintenance.LED 显示屏系统维护LED display system defend1 多块模组连续不亮或有特别multi-module cannot be continuumenlightened.(black screen)orabnormal检查信号方向第一块不正常模组的排线和电源线是否接触良好，如模组无 LED 亮，则说明无电源输入， 请检查电源局部可用万用表检查，如消灭花
32、色有颜色混乱的亮点则说明模组无信号输入，请检查第一块不正常模组的排线的输入端是否接触严密，可屡次拔插测试，如问题照旧可以调换的排线。Please check the first one unnormal module s parallel and the power line whether engage well,if LED cannot enlighten in module,so there is nopower supply,please checkthe power part (could checkit with multimeter ),if there is design a
33、nd coulour(have glitterring of confusion coulour)it indicate have no signal input,please check the first one unnormal modules parallel and the power line whether engage inseparable,you can remove it many times.2 单模组不亮single module cannot enlighten检查该模组的电源供给是否良好，主要是检查模组上的电源插座是否有松动。如整块模组消灭颜色混乱 或者颜色不全都
34、但有信号输入，有正确的画面则为信号传输排县接触不良，重插拔排线，或者更换测试过的排线。如更换良好的排线仍有同样问题，请观察PCB 板的接口是否消灭问题。Check this modiles power supply whether well,the main check is check modules poewr outlet whether become flexible .if wholemodule appear coulour confusion or coulour difference(but have signal input and have correct picture)
35、so signal transmit parallel contact unwell，remove parallel again,or change the used parallel。If had changed parallel still have the same problem,please examine PCB s interface whether have problem .3 单灯不亮问题检测方法single light cannot enlighten problem inspect method用万用表检查LED 是否损坏，假设灯坏了就按下面第 5 项换灯。具体测灯方法
36、：把万用表打到电阻 X1 档，指针式万用表黑表笔接LED 的正极，红表笔接负极数字表黑笔接负，红笔接正，假设LED 亮，所测的灯是好的，假设灯不亮，所测的灯是坏的。Use multimeter check LED whether damage,if ligth breakdown then press below the fifth item change light.the details of method as follows:turn multimeter to resistor X1,the pointer of multimeter black pen joined LEDanod
37、e,red pen joined cathode(numberal black pen joined cathode,red pen joined anode,if LED enlightened,the light is OK ,on the contrary, the light is bad.4 LED 坏点维护失控点LED damage maintenance(out of control point)经过单灯检测确认为 LED 损坏，则依据实际需求，选择性承受以下维护方法。Go through sigle light inspected confirm LED breakdown,t
38、hen according to realistic need,selectivity use following maintenance method.4.1 正面维护frontage maintenance用对应型号的螺丝刀从正面将固定面罩螺丝去除掉注留好意保螺丝，取下面罩，进展换灯请依据下面换灯方法换灯，换灯和胶体密封完毕后，将原面罩复原，上紧螺丝上螺丝时请留意不要压住灯，最终如有胶体残留在LED 外表请细心去除胶体。Use the correct screwdriver take-off the fixed face guard from the obverse side(pay at
39、tention retain the screw),take-off face guard,change light(please according to the method as follow change light), after change light and colloid seal up, take original face guard back ,take back screw (when take back screw please pay attation not press light), at last if there is colloid remain on
40、the suface of LED please careful clean the colloid.4.2 反面维护the reverse side defend用对应型号的螺丝刀从反面将螺丝去除掉注留好意保螺丝，拔掉信号排线，为安全请不要拔掉电源连接线，以防止意外，留神将模组从钣金孔中取出，移到箱体反面，然后依照正面维护方法对单个模组进展维护换灯请依据下面换灯方法换灯或者检修其它。Use the correct screwdriver take-off the fixed face guard from the obverse side(pay attention retain the s
41、crew),pullout signal parallel,because of the save problemPlease not pull out power connected line,prevent accident,take module from etal plate hole carefully,move to the backof box,then according to the frontage defend method to change light for single module (please according to the follow method t
42、o change linht)or examine and repair others.5 换灯change light将损坏LED 四周的胶体用尖利工具如镊子去除掉，并使LED 针脚清楚的表露在视线中，右手用镊子夹住 LED，左手用烙铁温度大约为 40 度左右，过高温度将对 LED 造成损伤接触焊锡，并做稍许停留不超过3 秒钟，如超过时间但并不到达拆卸要求，请冷却后再重尝试将焊锡溶化，用镊子将 LED 去掉。将符合要求的 LED 灯正确的插入PCB 电路板的孔中，LED 灯的长脚为正极，短脚为负极，PCB 上 “方孔”为 LED 正极针脚插孔，“圆孔”为 LED 的负极针脚插孔，将少许焊锡丝
43、溶化，黏合在烙铁头上，用镊子调整好LED 方向，使其平稳，将焊锡焊于LED 和 PCB 相连处，用一样类型的胶体PH 值=7密封好LED。Take off the colloid around the LED could use sharp instrument(such as tweezers),and let stitch appear out side,right hand take tweezers clip LED,left hand take soldering iron(the temperature about 40degree,the high temperature wil
44、l cause LED breakdown )contact with soldering tin,and a bit stay for a time(untake 3 second,if over the time but not achieve the dismount require, please after cooling then try it again )let soldering tin melt,then use tweezers take LED away . accord with requireLED insert PCB electric circuit plate
45、s hole,(LED lights long leg is anode ,the short one is cathode, “square hole” on the top of PCB is LED anode stitch plug,(circle hole” is LEDs cathode stitch plug),let a little soldering tin melt glutinous at the top of soldering iron ,then uetweezers adjust the directe of LED,make it stable,make so
46、ldering tin defend in the linked point of LED and PCB,use the same kind of collid(PH=7) seal up LEDLED 显示屏使用留意事项及日常维护LED display use attention and daily defend1 开关显示屏留意事项attention of open and close display1.1 开关挨次：开屏时：先开机，后开屏,关屏时：先关屏，后关机。先关计算机不关显示屏，会造成屏体消灭高亮点，烧坏行管，后果严峻。The proper order of oped and c
47、lose :open screen: first open the PC,then open screen. Close screen : first close the screen,then close PC.( when close PC not close the screen,will make screen appear high glittering,burn up pipeline，the consequence serious.)1.2 开关屏时，间隔时间要大于 5 分钟。When open and close screen,the interval time must 5minutes.1.3 计算机进入工程掌握软件后，方可开屏通电。Open screen and through electrify until PC get into project software.1.4 避开在全白屏幕状态下开屏，由于此时系统的冲击电流最大。Avoid open screen when the conaition of whole white screen ,because