《恒温磁力搅拌器操作规范.docx》由会员分享，可在线阅读，更多相关《恒温磁力搅拌器操作规范.docx（4页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、恒温磁力搅拌器操作规范Document Issue/Revision Status:文件发布/修订描述:Revision版本Release/revise Date 发布/修订日期Revise Outline制修纪要Author 作者Remark 备注Drafted by制订Checked by 审核Approved by 批准Department制订部门1. Purpose 目的：Standardize the use and maintenance of temperature magnetic sti】rer , guide the safe operation, improve work
2、 efficiency .ensure the accurate and reliable of measurement.规范恒温磁力搅拌器的使用和维护，指导平安操作，提高工作效率，确保测量的准确可靠。2. Range 范围：Apply tothe use and maintenance of the temperature magnetic stirrer.适用于恒温磁力搅拌器的使用和维护保养。3. Responsibilities 职责：3. 1. Quality Department calibration center is 】esponsible for periodic calib
3、ration of the tempeialure magnetic stirrer, repair, inspection, and to guide he user correct operate and maintenance the device.3.1. 品质部计量中心负责的恒温磁力搅拌器检定、维修、校检，并指导操作者正确使用及保养。3. 2. The user shouldin accordance with the temperature magnetic stirrer operation specification .Proper use, routine inspectio
4、n, maintenance and delivery on schedule.3.2. 各使用部门应按照的恒温磁力搅拌器操作规范正确使用、II常检查、维护保养及到期送检。4. Schematic diagram of the instrument 仪器平面示意图: :chrome cross镀铭十字节：rubber chuck橡胶夹头(3): chrome-plated temperature sensor 镀铭温度感应立杆：chrome heating plate 镀铭加热盘：work lights工作指示灯：temperature display 温度显示屏：Power switch电源
5、开关: Magnetic rotation control knob磁力旋转控制旋钮T : Set / OK设定键/确定键(9)-2: Temperature Add button温度“加”键-3: Temperature minus” button温度“减”键5. Steps操作步骤：5. 1. Preparation before use5.1. 使用前准备工作1. 1. Power: Plug the power cord before use, to ensure stable power during use.5.1.1. 电源：使用前将电源线插紧，确保使用过程中电源稳定。5. 1.
6、 2. According to the volume of the reaction solvent, select the appropriate container and a suitable stirrer, place the container in the middle of the chrome plate, check the work status of the stirrer.5.1.2. 根据反响的溶剂量大小，选取合适的容器和合适的搅拌子，容器置于镀铭盘正中，检查搅拌子工 作情况。5. 2. start work5. 2.开始工作5. 2. 1. Place the
7、stirrer in the container carefully.And avoid the damagedby entry stirrer into the container rudely.5. 2.1.将搅拌子小心置于容器中，防止直接投入损坏容器。5. 2. 2. Put the mixing container which needstirrer on the chrome plate, add the reaction solution.5. 2. 2.把所需搅拌的容器放在镀铭盘正中，加入反响的溶液。5. 2. 3. Turn on the power and turn on t
8、he speed switch, the indicator light, it began to work.5. 2. 3.接通电源并翻开电源调速开关，指示灯亮，即开始工作。5. 2. 4. speed gradually adjusted, from low speed to high speed, does not allow high-speed gear directly to start, avoid the jitter since the different speed.5.2.4.调速由低速逐步调至高速，不允许高速档直接启动，以免搅拌子不同步引起跳动。6. Inspectio
9、n and maintenance 点检和保养6. 1. Inspection methods: Check the temperature using temperature collector or digital thermometer, the error 士 2 06.L点检方法：点检温度采用温度采集器或数字温度计，误差2。6. 2. Maintenance methods:6.2. 保养方法：6. 2. 1. Cut off the power, when there is the endL 不工作时应切断电源。6. 2. 2. The instrument should be k
10、ept clean and dry. Strictly prohibited solution into the machine will damage the machine, this is forbid. Avoid violent vibration, because violent vibration will make the internal contact points off.7. 2.2. 仪器应保持清洁干燥，严禁溶液进入机内，以免损坏机件。防止剧烈振动，以免内部接触点接 触处脱落。8. 2. 3. Keep the instrument clean and dry , a
11、void covered with chemicals.9. 2.3.保持仪器的清洁与干燥防止与化学药品接触。7. Precautions 考前须知：7. 1. speed from low speed gradually transferred to high speed, does not allow high-speed gear directly to start, avoid the jitter since the different speed.7.2. 调速由低速逐步调至高速，不允许高速档直接启动，以免搅拌子不同步引起跳动。7. 2. No stirring ,no heat.
12、Have switch control the heat.7. 2.不搅拌时不能加热，加热由开关控制。7. 3. When there is the end, adjust the magnetic rotation control knob to the lower power,to avoid splashing damaged the instrument at the begin of the next turn.8. 3.使用完毕将磁力旋转控制旋钮置于最小处，以免下一次使用时溶液飞溅或导致仪器损坏。9. 4.If lights does not work,change the lamp, and havea necessary check.10. 4.工作指示灯不亮时应及时更换灯泡，并做必要的检查。