《12V电源适配器K-8828BXY1产品规格书.pdf》由会员分享，可在线阅读，更多相关《12V电源适配器K-8828BXY1产品规格书.pdf（11页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、 电源适配器电源适配器规格书规格书 1、描述描述/DESCRIPTION:本规格书适应于 K-8828B1205000 型号的开关电源.The purpose of the document is to specify the functional requirements of a 60W switching power supply.2、输入特性、输入特性/INPUT CHARACTERISTICS:2.1 输入电压/Input Voltage:额定电压/Rated Voltage:100240Vac 调整范围/Variation Range:90-264Vac 2.2 输入频率/Inpu
2、t Frequency:额定频率/Rated Frequency:50/60Hz.调整频率/Variation Frequency:47-63Hz 2.3 输入电流/Input Current:当输入交流电压为额定值的下限电压负载满载时,最大输入交流电流 1.5A.1.5Amps max At any input voltage and rated,DC output rated load.2.4 浪涌电流/Inrush Current:当输出为额定负载,环境温度为 25,输入 240Vac 冷态起机时的最大浪涌电流小于 50A.50 Amps Max.Cold start at 240Vac
3、 input,with rated load and 25 ambient.2.5 AC 漏电流/Ac Leakage Current:当输入电压 240Vac 时,最大漏电流为 0.25mA.0.25mA Max.At240Vac input.金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 3、输出特性输出特性/OUTPUT CHARACTERISTICS:3.1 输出功率/Power output 电压 Idling Voltage 最小负载 Min.Load 额定负载
4、 Rated.Load 空载电压 Idling Voltage 输出功率 Output power 12-12.5Vdc 0.01A 5A 11.7-12.5V 60 W 3.2 负载特性,调整率/Combined Load/Line Regulation 3.3 纹波和噪音 Ripple and Noise:测试条件:在额定电压及额定负载条件下,使用示波器带宽为 20MHz 连接到充电器的输出端,同时输出端并联一个47uF 的电解电容和一个 0.1uF 的瓷片电容.Under nominal voltage and nominal load,the ripple and noise are
5、as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point.电压 最大纹波/最大噪音 Voltage Ripple and Noise(Max.)+12Vdc 300mV p-p 3.4 启动延迟时间/Turn on delay time:当输入 115Vac 和输出最大负载时,最大启动时间为 5S.5Second Max.at 115Vac input and output Max.load.3.5 上升时间/Rise time:当
6、输入 115Vac 和输出最大负载时最大时间为 80 mS.80 mS Max.at 115Vac input and output Max load.3.6 保持时间/Hold up time:当输入 115Vac 和输出最大负载时,最小保持时间为 5 mS.5 mS Min.at 115Vac input and output Max.Load.3.7 效率/Efficiency:当输入 100Vac 和输出最大负载时,最小 V.VMin.at 100Vac input and output Max.Load.当输入 240Vac 和输出最大负载时,最小 V V Min.at 240Vac
7、 input and output Max.Load.金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 3.8 过冲/Overshoot:在电源开启或关闭的时候,最大 15%.15%Max.When power supply at turn or turn off.4、保护功能保护功能/PROTECTION FUNCTION:4.1 短路测试/Short circuit test:该电源供给器在短路解除时能正常工作恢复.The power supply will be aut
8、o recovered when short circuit faults remove.4.2 过流保护/Over current Protection:过流 9AMax 故障排除后,电源将自动恢复正常工作.The power supply will be auto recovered when over current 9AMax faults remove.4.3 过压保护/Over Voltage Protection:当输出电压超过额定电压的 150%180%时,电源将保护,故障排除后能恢复正常工作.The power supply will auto recovered when
9、faults remove 150%180%.5、环境要求、环境要求/ENVIRONMENTAL REQUIREMET:5.1 工作温度/Operating Temperature:0-40,满载,正常工作.0 to 40,Full load,Normal operation.5.2 储藏温度/Storage Temperature:-20 to 80 带外壳/With package 5.3 振动/Vibration:1.测试标准:国际电工电子委员会 Operating:IEC 721-3-3 3M3 59Hz,A=1.5mm 加速度(9200Hz,Acceleration 5m/S2)2.
10、运输/Transportation:IEC 721-3-2 2M2 5-9Hz,A=3.5mm 9200Hz,加速度 Acceleration=5m/S2 200500Hz,加速度 Acceleration=15m/S2 金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 3.轴向振动/Axes,10 cycles per axis.在测试过程中不能出现永久性的损坏.No permanent damage may occur during testing.在电源开启和关闭后,样
11、机能够恢复到最初条件.The SAMPLE has to restore to its original situation after power off/on.5.4 跌落试验/Dropping Packed:插墙式跌落高度为 1200mm、桌面式跌落高度为 1000mm；1.2M for wallmount type and 1000mm for desktop type as above described;测试台面是厚 13mm 的夹木板，离地面高 19-20mm The horizontal surface consists of hardwood at least 13mm th
12、ick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.6、安全及、安全及 EMI 要求要求/SAFETY AND EMI REQUIREMENT:6.1 安全:符合标准 GB4943-2001.Safety:accord with GB4943-2001.6.2 高压/DIELECTRIC STRENGTH Hi-Pot:初级对次级/Primary to secondary:3000VaC/5mA/3S
13、for type test.6.3 绝缘抗阻/Iusulation resistance:初级对次级/Primary to secondary:10M min at 500V DC.6.4 爬电距离6.5mm 6.5 EMI 标准/EMI STANDARD Meets the Limits of/测试符合 IEC/EN60335,（参考标准）金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 7、结构参数结构参数/MECHANICAL REQUIREMENT:7.1 外壳/En
14、closure:（可以适当更改，大小合适即可，下面的尺寸为目前使用的）外壳尺寸:L105.5 x W46.5 x H30mm;The power supply size:L105.5x W46.5 x H30mm;7.2 输入线/Input Connector:（材质要求较软，工作温度可以考虑适用范围：-2040）2 Pin CN 插脚/Two pin input plug of CN.金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 8、线材、线材/CORD:具体根据客户需
15、求!/Specific according to customer demand!金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 9、铭牌、铭牌/LABEL:具体根据客户需求!/Specific according to customer demand!备注/Remarks:1.标签尺寸/Label size:2.标签材质/Label Material:黑底白字，光面/Black ground white character,Smooth 3.标签厚度/Label thic
16、kness:0.2mm 4.误差/Tolerance:0.2mm 5环保/ROHS 金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 10、包装说明包装说明/PACKING:金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 11、测试报告测试报告/ELECTRICAL TEST REPORT:No序号 Test item 测试项目 Test conditio
17、n 测试条件 Standard spec 标准规格 Test data 测试数据 Unit 单位 Judge 判定 1 3 4 5 Pass/Fail 1 Output V oltage 输出电压 Vin100Vac 60Hz Io=0 输入100Vac空载 12-12.5V 12.28 V PASS 2 Output V oltage 输出电压 Vin100Vac 60Hz Io=Rated Current 输入100Vac 60Hz额定电流 11.7-12.5V 11.86 V PASS 3 Efficiency(Full load)效率满载 Vin 115V ac 60Hz 输入115V
18、ac 60Hz V 85.7 PASS 4 Ripple&Noise mVp-p 纹波&杂讯 Vin100Vac 60Hz Full load 输入100Vac 60Hz满载 300mVp-p Max 105 mVp-p PASS 5 Line Regulation 线性调整率 Vin=100V240V Io=Rated Current 额定电流 2%/PASS 6 Standby Power 待机功耗 Vin 115V ac 60Hz Io=0 输入115Vac 60Hz 0.5W 0.18 W PASS 7 Short circuit test 短路测试 Vin100Vac 60Hz 输入
19、100Vac空载 No odor smoke fire plastic deformation and excessive heat happen.无冒烟,起火,外壳变形及过热现象 ok PASS 8 OCP 过电流保护 Vin100Vac 60Hz 输入100Vac空载 9AMax ok A PASS 9 Output V oltage 输出电压 Vin240Vac 50Hz Io=0 输入240Vac空载 12-12.5V 12.28 V PASS 10 Output V oltage 输出电压 Vin240Vac 50Hz Io=Rated Current 输入240Vac 60Hz额定
20、电流 11.7-12.5V 11.86 V PASS 11 Efficiency(Full Load)效率满载 Vin230Vac 50Hz 输入230Vac 50Hz V 86.9%PASS 12 Ripple&Noise mVp-p 纹波&杂讯 Vin240Vac 50Hz Full load 输入240Vac 50Hz额定电流 300mVp-p Max 124 mVp-p PASS 13 Line Regulation 线性调整率 Vin=100V240V Io=Rated Current 输入100V240V 2%/PASS 14 Standby Power 待机功耗 Vin230Va
21、c 50Hz Io=0 输入230V 50Hz 0.5W 0.33 W PASS 15 Short circuit test 短路测试 Vin240Vac 50Hz 输入240Vac 50Hz No odor smoke fire plastic deformation and excessive heat happen.无冒烟,起火,外壳变形及过热现象 ok PASS 16 OCP 过电流保护 Vin230Vac 50Hz 输入230Vac 50Hz 9AMax ok PASS 17 Hi-pot test 高压测试 高压/DIELECTRIC STRENGTH Hi-Pot:初级对次级/P
22、rimary to secondary:3000Vac/5mA/3S for type test ok PASS 18 Burn in 老化 Input:220Vac/50Hz Full Load 4hrs 输入 220Vac/50Hz满载 4 小时 ok PASS 19 Drop test 跌落 Heigh:1m Three*faces(onceon each plane)高 1 米,6 个面,每面 1 次.ok PASS REMARK 备注 金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 12、原理图原理图/ELEMENTS DRAWING：金宝通金宝通/BESTGK 电源适配器电源适配器 K-8828B 版本版本/Version SHEETSHEET OFOF R&D Power adapter A1A1 13、PCB 丝印图丝印图/PCB SILK-SCREEN DRAWING：金宝通金宝通/BESTGK R&D 电源适配器电源适配器 Power adapter K-8828B 版本版本/Version SHEETSHEET OFOF A1A1