《QY IMR18650-1500产品规格书.doc》由会员分享，可在线阅读，更多相关《QY IMR18650-1500产品规格书.doc（9页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、东莞市百超电子科技有限公司编 号：版 次: 页 码： Specification for Li-ion Rechargeable cylindrical battery圆柱锂离子电池规格书MODEL/型号: IMR18650-1500mAh IMR18650-2000mAhPrepared By/Date编 制/日 期Checked By/Date审 核/日 期Approved By/Date批 准/日 期CustomerApproval 客户批准Signature 确认Date 日期Company Name：公司名称：Company Stamp：客户印章：1 适用范围Scope of app
2、lication本产品规格书适用于IMR18650圆柱锂离子电池。Apply to IMR18650 Li-ion battery.2 产品基本特性技术参数Basic Properties 项目Item技术参数Technical parameter1电池类别Class圆柱锂离子可充电池Li-ion Rechargeable cylindrical battery2电池型号ModelIMR186503额定容量Nominal capacity1500mAh（6.3.1）4内阻Internal resistance60m5标称电压Nominal voltage3.7V6最高充电电压Max. char
3、ging voltage4.20V0.03V7放电最低终止电压Min. end voltage3.00V8贮存和运输电压Voltage at Storage and transport3.6V-4.0V9最大持续充电电流Max. constant charging current1500mA10最大持续放电电流Max. constant discharging current3000mA11充电温度范围Charging Temp Range04512放电温度范围discharging Temp Range-206013贮存温度范围Storage Temp Range-204514外形尺寸Con
4、tour size如附图2所示 figure 215单体重量weinght41g16极性Positive and negative（+）:盖帽Cover（-）:壳体Can17环境物质environmental matters符合ROHS产品外观Appearance外观整洁，电池表面不应有明显变形、凹点、锈斑，划伤，裂纹，污迹，和漏液等不良缺陷。There shall be no such defects as deep scratch, crack, rust, discoloration or leakage, which may adversely affect the commercia
5、l value of the battery.3 产品重要电性能Important electrical properties3.1 循环寿命Cycle Life3.1.1 300次3.1.2 45min3.1.3 循环期间不漏液No leakage3.2 温度特性Temperature Characteristic3.2.1 -20放电Discharge performance at -20：180min3.2.2 0放电Discharge performance at 0：240min3.2.3 55放电Discharge performance at 55：51min3.3 荷电保持能力
6、Capacity retention：255min 4 哦产品安全性能 Safety properties4.1 机械碰撞Shock Test：5 不泄漏，不泄放，不起火，不爆炸 No leakage, no venting ,no fire, no explosion5.1 机械振动Vibration Test：不泄漏，不泄放，不起火，不爆炸No leakage, no venting ,no fire, no explosion5.2 高温贮存：不泄漏，不泄放，不起火，不爆炸No leakage, no venting ,no fire, no explosion5.3 温度循环Tempe
7、rature Cycling Test：不泄漏，不泄放，不起火，不爆炸No leakage, no venting ,no fire, no explosion5.4 高空模拟Altitude Simulation(low pressure) Test：不泄漏，不泄放，不起火，不爆炸No leakage, no venting ,no fire, no explosion5.5 短路Short -circuits Test：不起火，不爆炸，表面温度不超过150No fire, no explosion and the exterior temperature of the battery sh
8、all not exceed 1505.6 过放Forced-Discharge Test：不起火，不爆炸 No fire, no explosion5.7 过充Overcharge Test：不起火，不爆炸No fire, no explosion5.8 跌落Free fall Test：不起火，不爆炸No fire, no explosion5.9 挤压Crush Test：不起火，不爆炸No fire, no explosion5.10 高温搁置Thermal Exposure Test：不起火，不爆炸No fire, no explosion6 测试Test6.1 测试条件Standa
9、rd Test Environment(特殊注明的除外Unless otherwise stated）6.1.1 温度Temperature：2526.1.2 相对湿度Relative humidity：45%-75%6.1.3 大气压力Pressure：86KPa-106KPa6.2 测量公差Parameter measure tolerance6.2.1 尺寸Size：0.1%6.2.2 电流Current: 1%6.2.3 电压Voltage: 1%6.2.4 内阻Internal resistance：2m6.2.5 容量Capacity：10mAh6.2.6 温度Temperatur
10、e：26.2.7 湿度Relative humidity：5%6.2.8 时间Time：1min6.3 测试方法Testing Method6.3.1 容量Capacity在6.1的条件下存放4小时，充电：以750mA恒流充电至4.20V，然后4.20V恒压充电至电流小于20mA时终止，搁置5分钟；放电：以750mA恒流放电至3.0V的容量（可重复5次，有一次合格即可终止）。In a Condition of 6.1, Charge: charge the battery to 4.2V with Current of 750mA, then to 20mA with Constant Vol
11、tage of 4.2V ,rest for 5 min.Discharge: discharge the battery to 3.0V with Current of 750mA ( repeat the processing 5 times, It can be ended if capacity is up to grade one time).6.3.2 内阻Internal resistance使用内阻仪测量，电池处于40%-60%荷电态。Measured With internal impedance equipment at with 40%60% charging of th
12、e battery.6.3.3 电压Voltage使用万用表直流电压档20V量程测量或电压表5V量程。Measured With 20V rangeability of the multimeter or 5V rangeability of the voltage meter.6.3.4 电流Current使用万用表直流电流档15A量程串联测量。Measured With DC 15A rangeability of the multimeter in series.6.3.5 温度Temperature使用带耐高温引线数字温度仪测量Measured With digital tempera
13、ture meter by the high temperature resistance down-lead.6.3.6 尺寸Size长度使用数显卡尺测量，厚度使用数显千分尺测量Measured length With digital calipers,t Measured thickness With digital micrometer.6.3.7 重量Weight使用0.1g的电子天平测量Measured With 0.1g digital electronic balance 6.3.8 外观Appearance目视检测eye survey6.3.9 循环寿命Cycle Life按6
14、.3.1的方法，完成一次为一个循环，重复以上循环，直至连续三次放电时间小于45分钟，则认为循环寿命终止，循环测试应符合4.1的要求。According to 6.1 and 6.3.1, repeat this processing, When continuous three times discharging time less than 45 min , the cycles is finished6.3.10 温度特性Temperature Characteristic按6.3.1的要求充电，然后将电池转到4.2.1或4.2.2或4.2.3相应温度的环境中，搁置4小时，然后在相应环境中
15、以0.2C电流放电至2.75V，放电时间应符合4.2中相应温度的要求。Charge according to 6.3.1, store the battery 4h under appointed temperature ,and discharge the battery to 2.75V with the current of 0.2C to 2.75V6.3.11 荷电保持能力Capacity retention在6.1的条件下，电池充电后贮存28天，然后以0.2C放电至2.75V，放电时间应符合4.3的要求。According to 6.1 and 6.3.1， charge the
16、battery, and store the battery on open circuit for 28 days, then discharge the battery with 0.2CA to 2.75V.6.3.12 荷电恢复能力Capacity recovery after storage在6.1的条件下，按6.3.1的方法测一次容量，电池在放电态下，在402条件下开路存放90天。贮存结束后，再按6.3.1的方法检测一次容量，符合4.4的要求。According to 6.1 and 6.3.1 ,test the capacity of the battery,after the
17、 battery have be discharge, store it, in open circuit, in ambient temperature of 402 for 90 days，then according to 6.1 and 6.3.1 ,test the capacity of the battery.6.3.13 机械碰撞Shock Test电池采用刚性固定的方法，在两个相互垂直的方向上承受两次等值的冲击。每次冲击应在电池表面垂直的方向上按下述方法进行：在最初的3ms内，最小平均加速度为75gn（gn为当地的重力加速度），峰值加速度应在125gn和175gn之间，波形为
18、半正弦波。The battery is to be secured to the testing machine by means of a rigid mount .Each battery shall be subjected to a total of two shocks of equal magnitude. The shocks are to be applied in each of mutually perpendicular directions. Each shock is to be applied in a direction perpendicular to the
19、face of the battery. For each shock the battery is to be accelerated in such a manner that, during the initial 3ms, the minimum average acceleration is 75 gn (where gn is the local acceleration due to gravity).The peak acceleration shall be between 125 gn and 175 gn .The waveform should be half-sine
20、6.3.14 机械振动Vibration Test将电池固定在振动装置上，对电池施加振幅0.8mm（双振幅1.6mm），频率变化1Hz/min，频率范围10Hz-55Hz的简谐波，振动持续时间90min-100min，电池分别承受相互垂直的两个方向的振动。The battery shall be subjected to a simple harmonic motion with an amplitude of 0.8 mm 1.6 mm total maximum excursion. The frequency is to be varied at the rate at the rate
21、 of 1 Hz per minute between 10 and 55 Hz. The battery shall be tested in two mutually perpendicular directions.6.3.15 高温贮存High temperature storage test电池放于752烘箱中，搁置48h。The battery shall be exposed to a temperature of 752 for 48 h in an oven6.3.16 温度循环Temperature Cycling test将电池放在专用烘箱中,在30分钟内将温度升至703
22、,并恒温4h，在30分钟内降温至203，恒温2h，在30分钟内降温至-403,恒温4h，在30分钟内升温至203，重复以上过程9次，在第10次循环后贮存7天。Raising the chamber-temperature to 703 within 30 minutes and maintaining this temperature for 4 hoursReducing the chamber temperature to 203 within 30 minutes and maintaining this temperature for 2 hours.Reducing the cham
23、ber temperature to日-403 within 30 minutes and maintaining this temperature for 4 hoursRaising the chamber temperature to 203 within 30 minutesRepeating the sequence for a further 9 cyclesAfter the 10th cycle, storing the battery for 7 days prior to examination6.3.17 高空模拟Altitude Simulation将电池在203，大气
24、压力11.6KPa的条件下放置6hSamples are to be stored for 6 hours at an absolute pressure of 11.6kPa and a temperature of 2036.3.18 短路Short -circuits test电池应在外电路总电阻小于100m的条件下,分别在252和602的环境温度下进行短路试验,当电池电压低于0.1V或电路不进一步放电,同时电池壳温度恢复至初始环境温度的10范围内,结束试验。The battery shall be subjected to a short-circuit condition with
25、a total external resistance of less than 100m.Two separate tests shall be conducted, one in an ambient temperature of 252 and one in an ambient temperature of 602.The test shall be continued until the battery voltage falls below 0.1 V ,and the battery case temperature has returned to a value within
26、10 of the original ambient temperature.6.3.19 过放Forced-Discharge test将电池与不低于10V的电源串联,以0.2CA的电流恒流放电。试验持续12.5h。即使电池电压达到0V后,试验应继续进行。The battery shall be subjected to a discharge at a constant current of 0.2C by connecting it , in series, to a power supply not less than 10V. The duration of the test sha
27、ll be 12.5h.This test shall be continued even after the battery reaches 0V.6.3.20 过充Overcharge test首先将电池以0.2C放电至规定的终止电压，连接正负极于一恒流恒压电源,调节电流至3C，电压为4.5V，充电时间为tc=48小时。The battery shall be discharged at a constant current of 0.2C to cut-off voltage and shall be recharged with 3C,by connecting it to a pow
28、er supply of equal to 4.5V. the test time tc should be 48 hours. 6.3.21 跌落Free fall test将电池充满电的电池从1.0m的高度上跌落到放置在水泥地面上5cm厚的硬木板上，每个电池跌落6次。Each battery shall be dropped 6 times from 1.0 m onto a hard wood floor with 5cm height. 6.3.22 挤压Crush test将充满电池的电池放置在两硬木(厚度至少为12.7mm)之间进行挤压。逐渐增大压力至13KN,然后减小压力直至脱开
29、，挤压时电池的长轴方向应与挤压板保持平行。还应在长轴与挤压板垂直方向进行试验。每只电池只允许在一个方向上进行一次挤压试验，每次试验采用不同的电池。The battery of fully charged shall be crushed between two flat hardwood blocks with a thickness of at least 12.7 mm using a crushing apparatus capable of applying a force of 13kN. The force is gradually decreased until escape f
30、orm the hardwood. The battery shall be crushed with its longitudinal axis parallel or vertical to the flat surfaces of the crushing apparatus. Each battery shall be subjected to a crushing force in only one direction. Different battery shall be used for each test.6.3.23 高温搁置Thermal exposure test电池应放
31、置于加热箱中,加热箱应以(52)/min的速率升温至1302,并恒温15min。The battery shall be placed in an oven. The oven temperature shall be increased at a rate of 52 per minute until the oven reaches 1302.The oven shall be maintained at 1302 for 15 min7 包装Packing 附图1 包装示意图Packing figure8 贮存8.1 电池若长期储存，要保持在50放电态。Battery should be
32、 in 50% charge if it is stored for a long time.8.2 电池应保存在低温干燥的环境中。Battery should be stored under low temperature and dry environment.8.3 电池储存时要远离热源，也不能置于阳光直射的地方。Battery should be stored away from the heat source and place where sunlight focus on.8.4 电池储存时，应每三个月对电池电压进行一次检查，如果电压低于3.5V，应对电池补充电到3.9V。Che
33、ck the battery every 3 months when it is stored, and charge the battery to 3.9V if the voltage is below 3.5V.9 注意事项Important Notice9.1 请勿直接串联使用。Cant use directly in series connection of many batteries.9.2 仅在指定的设备上使用电池。Only used on specified instrument.9.3 不要把电池同干电池或其他原电池一起使用，也不要同不同包装、不同型号或不同品牌的电池一起使
34、用。Do not use the together with different kind of or different type of battery.9.4 不要把电池投入水中，也不要弄湿。Do not drop the battery into water, and do not make the battery wet.9.5 不要用金属短路电池的正负极。Do not short circuit the battery by metal conductor.9.6 在装入设备时注意电池的正负极不要反装。Be sure not to use the battery by reverse
35、 anode/cathode.9.7 不要对电池进行分解。Do not disassemble the battery.9.8 不要使用带有严重伤痕或变形的电池。Do not use bad scar battery.9.9 在使用之前请详细阅读操作说明书，不适当的操作可能引起的电池变热、着火、爆炸、毁坏或电池容量的衰减。Please read the operation guidebook carefully before using the battery, because the inappropriate operation may cause overheat, catching f
36、ire , explosion or making capacity decrease.9.10 如果电解液渗透到你的皮肤或衣服上，立刻用清水清洗。Wash yourself quickly when electrolyte infiltrating to your skin or clothes9.11 如果电解液渗出并进入你的眼睛里，不要揉擦你的眼睛，立刻用干净的水清洗并去医院检查。Wash your eyes by clean water quickly and go to hospital for further check, if the electrolyte infiltrate
37、 to your eyes.9.12 电池寿命终止后要立即从设备中取出。Take out the battery when its life time is over.9.13 当长期不用时，要将电池从设备中取出，在常温条件下保存，并定期充放电。Take out the battery and keep it under low temperature and low humidity when the battery is not used for a long time.9.14 如果电池的接线端变脏，在使用之前用干布擦净。Clean the battery with dry cloth
38、before use if the connection of the battery is dirty.10 警告Warning10.1 不要把电池放在发热装置，洗衣机或高压容器中。Do not place the battery on heater, washer or high-pressure container.10.2 不要把电池加热或投进火中。Do not heat the battery and drop to the fire.10.3 如果在规定的充电时间内充电没有结果，停止充电。Stop charging if you get no result during speci
39、fied time.10.4 不要把电池同项链、发夹、硬币或螺丝等金属品一起放在兜中或包中，也不要把电池同上述物品一起储存。Do not lay the battery with the necklace, coins, and other metal items together.10.5 在使用、充电或储存期间如发现电池有变热、散发气味、变色、变形或其他反常之处停止使用。Stop using when the battery become heat, emit smell or appear other abnormality during use, charging, or storin
40、g.10.6 不要在火源附近或温度超过60的环境中使用或遗留电池，也不要在这些环境中进行充放电。Do not use battery or leave the used battery in the environment over 60,and do not charge and discharge under this kind of environment.10.7 当发现电池漏液或散发出难闻的气味时立即远离。Keep away from the battery which is leakage or emit abnormal smell.10.8 把电池放在小孩够不到的地方以免引起危
41、险。Keep it away from the children, avoiding being swallowed.11 东莞市青源电子科技有限公司保留对规格书更改的权利，若对此技术规格书有疑问或意见不一致处，请与本公司联系。Dongguan QINGYUAN Electronics Technology Co., Ltd keep the right to change the specification, Please contact with us If you disagree or have any doubt with this specification.附图2 电池外形尺寸型号name电池外径outside diameter电池总高Htotal heightIMR1865018.000.05（mm）64.900.10（mm）