《MP128FL-T规格书.pdf》由会员分享，可在线阅读，更多相关《MP128FL-T规格书.pdf（11页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、 SPECIFICATION 产品规格书产品规格书 Revision:1.0 Issued Date：2011-06-21 Model No.:MP128FL-T Description:LED Power Supply Specification PREPARED BY 编写编写 CHECKED BY 审核审核 APPROVED BY 批准批准 纪应龙纪应龙 冉洪江冉洪江 詹星詹星 深圳市麦格米特电气股份有限公司深圳市麦格米特电气股份有限公司 SHENZHEN MEGMEET ELECTRICAL CO.,LTD Add:深圳市南山区科技园北区朗山路紫光信息港 A 座 5 楼 Tel:075
2、5-86600500 Fax:0755-86600999 E-mail:;http:/ Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 2 of 11Page 2 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Revision History 修订履历修订履历 Revision 版本/次 Change Item (修改项次)Date (修改日期)1.0 Ini
3、tial Release(初版发行)2011/06/21 Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 3 of 11Page 3 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Section 目录 Section 目录 1.Power supply overview 电源性能指标 1.Power supply overview 电源性能指标 1.1 Inp
4、ut Electrical Characteristics Overview（输入特性）（输入特性）1.2 Output Electrical Characteristics Overview（输出特性）（输出特性）1.2.1 Output Voltage,Current&Regulation.（输出电压电流调整率）（输出电压电流调整率）1.2.2 DC Output Ripple&Noise.（输出纹波和噪声）（输出纹波和噪声）1.2.3 Output Transient Response.（输出动态响应）（输出动态响应）1.2.4 DC Output Hold-Up Time.（输出保持时
5、间）（输出保持时间）1.2.4 DC Output Overshoot At Turn On&Turn Off.（输出超调）（输出超调）1.2.6 DC output voltage rise time（输出上升时间）（输出上升时间）1.3 Remote On/Off Control：（遥控功能）：（遥控功能）1.4 Protection:（保护功能）（保护功能）1.4.1 DC output Over Voltage Protection.（输出过压保护）（输出过压保护）1.4.2 DC Output Over current Protection.（输出过流保护）（输出过流保护）1.4.3
6、 DC Output Short Circuit Protection.（输出短路保护）（输出短路保护）1.4.4 Reset After Shutdown.（保护功能复位）（保护功能复位）2.Isolation 绝缘性能 3.2.Isolation 绝缘性能 3.Safety 安全规格 4.EMC 电磁兼容性 4.1 EMI（电磁干扰）4.2 EMSSafety 安全规格 4.EMC 电磁兼容性 4.1 EMI（电磁干扰）4.2 EMS（电磁抗扰）5.Environmental Requirement 环境（电磁抗扰）5.Environmental Requirement 环境 5.1 Te
7、mperature（环境温度）5.2 Humidity（环境湿度）5.1 Temperature（环境温度）5.2 Humidity（环境湿度）5.3 Altitude（海拔高度）5.3 Altitude（海拔高度）5.4 Cooling Method（冷却方式）5.5 Vibration（振动耐受）5.4 Cooling Method（冷却方式）5.5 Vibration（振动耐受）5.6 Impact（冲击耐受）5.6 Impact（冲击耐受）6.Dimension（物理尺寸）Dimension（物理尺寸）7.7.Weight（重量）Weight（重量）8.Pin Connection(连
8、接器脚位定义)9.8.Pin Connection(连接器脚位定义)9.Power Supply mounting（安装尺寸）10.Power Supply mounting（安装尺寸）10.Package(包装包装)Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 4 of 11Page 4 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T 1.Power Sup
9、ply Overview 电性能指标电性能指标:1.1 Table 1 Input Electrical Characteristics Overview（输入特性）（输入特性）Input voltage range Input voltage range 输入电压输入电压 90Vac to 264Vac Normal voltage range标称输入100Vac to 240Vac Frequency range 频率范围 50Hz/60Hz5%Max input ac current 满载输入电流 4.5Amax at full load and 90Vac condition Inru
10、sh current(cold start)浪涌电流 50Atyp peak,120Vac;100Atyp peak,220Vac Efficiency(full load)效率 83%min at 90Vac;86%min at 220Vac Typ.Harmonic current 谐波电流 Meet GB17625.1-2003/IEC61000-3-2 class D Leakage Current 泄漏电流 Less Than 0.5mA at 230Vac input Standby Power Loss 待机功耗 0.5W 240Vac input at 5Vsb Output
11、current20mA Input Fuse 输入保险 T6.3A/250Vac 1.2 Output Electrical Characteristics Overview（输出特性）（输出特性）1.2.1 Table 2 Output Voltage,Current&Regulation.（输出调整率）（输出调整率）Output Voltage 输出电压 Regulation 调整率 Min.current 最小电流 Rate current 额定电流 Peak current 峰值电流+V1(+24V)+V110%0.1A 6.5A 9.0A*+V2(+A24V)+V210%0.1A 1
12、.0A 1.5A*+V3(+12V)+V310%0.2A 0.2A-2.5A 3.5A*+V4(+5.0V)+V45%0.1 A 0.1A-3.0A 4.5A*+V5(+5.0VSB)+V55%0.01 A 0.5A 1A*Note:*The Max.current or power should be test at other of dc output at Rated load,And the peak current pulse width within 100ms 峰值电流或功率的测试是在其它额定负载时测试，且脉宽小于 100 毫秒。1.2.2 Table 3 DC Output R
13、ipple&Noise.（输出纹波和噪声）（输出纹波和噪声）Output Voltage Ripple&Noise(Max.)+V1(+24V)240mVp-p25;350mVp-p-10+V2(+A24V)240mVp-p25;350mVp-p-10+V3(+12V)120mVp-p25;200mVp-p-10+V4(+5.0V)50mVp-p25;150mVp-p-10;+V5(+5.0VSB)60mVp-p25;200mVp-p-10;150mVpp when STB Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Pag
14、e 5 of 11Page 5 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Note:1)Measurements shall be made with an oscilloscope with 20MHz bandwidth.示波器须设置在 20 兆赫兹带宽 2)Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a 10uF
15、electrolytic capacitor to simulate system loading.输出须并联 0.1uF 的陶瓷电容和 10uF 的电解电容来模拟负载 1.2.3 Output Transient Response.（输出动态响应）（输出动态响应）Table 4.Test condition.测试条件 Voltage Tolerance Limit Slew Rate Load Change 5.0V/5.0VSB5%24V/12V/10%0.2A/uS Min.to 50%load and 50%to Max load All output10%0.2A/uS Min.lo
16、ad to Max load Note:Transient response measurements shall be made with a load changing repetition rate of 50Hz to 10kHz.以 5010KHz 的频率跳变负载来测试。1.2.4 Table 5 DC Output Hold-Up Time.（输出保持时间）（输出保持时间）Output Voltage 120Vac input 220Vac input+V1(+24V)10 mS 10 mS+V2(+A24V)10 mS 10 mS+V3(+12V)10 mS 10 mS+V4(+
17、5.0V)10mS 10 mS+V5(+5.0VSB)10 mS 10 mS Note:All of dc output at full load.所有输出带满载 1.2.5 Table 6 DC Output Overshoot At Turn On&Turn Off.（输出超调）（输出超调）Over shoot voltage(V)超调电压 Output ChannelOutput(V)Turn on开机 Turn off关机+V1(+24V)+24V 10%10%+V2(+A24V)+24V 10%10%+V3(+12V)+12V 10%10%+V4(+5.0V)+5.0V 10%10%
18、+V5(+5.0VSB)+5.0V 10%10%Note:All of dc output current from Min.to Max.测试时负载范围：最小到最大 1.2.6 Table 7 DC output voltage rise time（输出上升时间）（输出上升时间）Output Voltage 120Vac input&Full 220Vac input&Full Load Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 6 of 11Page 6 of 11 The copyright belongs
19、 to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Load+V1(+24V)100mS 100mS+V2(+A24V)100mS 100mS+V3(+12V)100 mS 100 mS+V4(+5.0V)100 mS 100mS+V5(+5.0VSB)50 mS 50 mS Note:The output voltages shall rise from10%to 90%of their output voltage.输出从 10%上升到 90%的时间 1.3 Remote On/Off C
20、ontrol：（遥控功能）（遥控功能）The power supply DC outputs(without+5.0Vsb)shall be enable with an active-high TTL(2.5V/2.0mA)-compatible signal(Ps-on).The+5.0Vsb is on whenever the AC power is present.除 5.0Vsb 外，其余输出受控于一个 TTL 电平兼容的信号（Ps-on2.5V/2.0mA）,5.0Vsb 上电就存在。*When Ps-on is pulled to TTL high,the DC outputs
21、 are to be enabled.Ps-on 高电平，打开输出*When Ps-on is pulled to TTL low or open circuit,the DC outputs are to be disabled.Ps-on 低电平，关闭输出 Table 8.Ps-on Signal Comments Outputs Ps-on-high 2.5V&2.0mA(source)Output Ps-on-low 0.5V X Ps-on-open-X 1.4 Protection:（保护功能）（保护功能）1.4.1 Table 9 DC output Over Voltage P
22、rotection.（输出过压保护）输出过压保护）Output Voltage TYP.Over Voltage Comments+V1(+24V)+V2(+A24V)27V Power supply latch into shutdown state 输出锁机+V2(+12V)14V Power supply latch into shutdown state 输出锁机 Note:The power supply shall be test at max AC voltage(264Vac)and min load or no load.应该在最大交流输入电压 264 伏和轻载、空载下测试。
23、1.4.2 Table 10 DC Output Over current Protection.（输出过流保护）（输出过流保护）Output Voltage Over Current Comments Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 7 of 11Page 7 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Note:*The over cur
24、rent protection should be test at other of dc output at Rated load but the 24V over current protection should be test at 12Vdc output at min load.12V,5V 和 5VSTB 过流保护测试是在其它额定负载时测试.而 24V 过流测试是在 12V 轻载电流时测试。过流保护测试是在其它额定负载时测试.而 24V 过流测试是在 12V 轻载电流时测试。1.4.3 Table 11 DC Output Short Circuit Protection.（输出
25、短路保护）（输出短路保护）Output Voltage Comments+V1(+24V)Shutdown 锁机+V2(+A24V)Shutdown 锁机+V3(+12V)Shutdown 锁机+V4(+5.0V)Hiccup尝试重复启动+V5(+5.0VSB)Hiccup尝试重复启动 Note:*The Short Circuit protection should be test at other of dc output at Rated load 短路保护测试是在其它额定负载时测试短路保护测试是在其它额定负载时测试.1.4.4 Reset After Shutdown.（保护功能复位）
26、（保护功能复位）Recycle the ps-on signal,the power supply will restart after the fault removed.故障去除后，关掉 Ps-on 信号再打开，电源即可恢复。故障去除后，关掉 Ps-on 信号再打开，电源即可恢复。2.Isolation（绝缘性能）（绝缘性能）2.1 Table 12（绝缘阻抗）（绝缘阻抗）Input To Output DC500V 50Mmin(at room temperature)Input To FG DC500V 50Mmin(at room temperature)Output To FG N
27、on Isolated 2.2 Table 13（绝缘耐压）（绝缘耐压）Input To Output 3000Vac 50Hz 1minute 10mA Input To FG 1500Vac 50Hz 1minute 10mA+V1(+24V)10Atyp*Hiccup 尝试重复启动+V2(+A24V)2Atyp*Hiccup 尝试重复启动+V3(+12V)4Atyp*Hiccup 尝试重复启动+V4(+5.0V)4.5Atyp*Hiccup 尝试重复启动+V5(+5.0VSB)2.5Atyp*Hiccup 尝试重复启动 Document No.：Issued Date:2011-06-2
28、1 版权属于麦格米特,禁止任何未经授权的使用。Page 8 of 11Page 8 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Output To FG Non Isolated Note:Open FG and Output return.交流地和输出负极要断开。3.3.Safety （安全规格）（安全规格）The power supply shall compliance with the following Criterion
29、:The power supply shall compliance with the following Criterion:电源安全性满足下列标准 电源安全性满足下列标准 1)UL60950/UL60065 2)EN60950/EN60065 3)GB4943-1995/GB8898-2001 4.4.EMC （电磁兼容性）（电磁兼容性）4.1 EMI（电磁干扰）（电磁干扰）The power supply shall compliance with the following Criterion:The power supply shall compliance with the fol
30、lowing Criterion:电源电磁干扰满足下列规则：电源电磁干扰满足下列规则：1)1)Conduction Emission:Conduction Emission:（传导干扰度）（传导干扰度）*EN55013/EN55022,CLASS B*GB13837-2003,CLASS B*CISPR13:2001/FCC PART15 CLASS B 2)Radiated Emission:2)Radiated Emission:（辐射干扰度）（辐射干扰度）*EN55013/EN55022,CLASS B*GB13837-2003,CLASS B*CISPR13:2001/FCC PART
31、15 CLASS B 4.2 EMS（电磁抗扰）（电磁抗扰）The power supply shall compliance with the following Criterion:The power supply shall compliance with the following Criterion:电源电磁抗扰满足下列规则：电源电磁抗扰满足下列规则：1)ESD 1)ESD（静电抗扰度）（静电抗扰度）*GB17626.2-1998/IEC61000-4-2 2)EFT 2)EFT（脉冲群抗扰度）（脉冲群抗扰度）*GB17626.4-1998/IEC61000-4-4 3KV 3)Su
32、rge 3)Surge （雷击浪涌）（雷击浪涌）*GB17626.5-1998/IEC61000-4-5 1.5KV/3KV 5.Environmental Requirement （工作环境）（工作环境）5.1 Temperature（环境温度）（环境温度）*Operating:0 to+40.*Store:-20 to+80.5.2 Humidity（环境湿度）（环境湿度）*Operating:From 10%to90%relative humidity(non-condensing).*Store:From 5 to 95%relative humidity(non-condensing
33、).5.3 Altitude （海拔高度）（海拔高度）Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 9 of 11Page 9 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T *Operating:to10,000 ft.*Store:to 20,000ft.5.4 Cooling Method（冷却方式）（冷却方式）*Ventilation cooling.
34、自然冷却 5.5 Vibration（振动耐受）5.5 Vibration（振动耐受）*10-55Hz,19.6m/s(2G),3minutes period,60minutes each along X,Y and Z axis.5.6 Impact（冲击耐受）（冲击耐受）*49m/s(5G),11ms,once each X,Y and Z axis.6.Dimension（物理尺寸）（物理尺寸）*280mm 180mm 12mm(长 L*宽 W*高 H).板面高 7.Weight（重量）（重量）*约 600g 8.Pin Connection(连接器脚位定义连接器脚位定义)Table 1
35、5 Pin-CON4,CON5 Connection And Function NO.Pin Connection Function 5.6.7.8 GND+24VDC RETURN 1.2.3.4 +24V+24VDC OUTPUT Note:CON4-XH CONNEETION,TYPE:pitch2.5mm Table 16 Pin-CON3 Connection And Function NO.Pin Connection Function 3.4 GND+24VDC RETURN 1.2+A24V+A24VDC OUTPUT Note:CON3-XH CONNEETION,TYPE:
36、pitch2.5mm Table 17 Pin-CON2 Connection And Function NO.Pin Connection Function 1.2 GND+5V+5VSB+12VDC RETURN 3.4+5V+5VDC OUTPUT 5 STB SMPS ON/OFF CONTROL(ON=HIGH)6+5VSB STANDBY(+5.0VDC)OUTPUT 7.8+5V+5VDC OUTPUT 9.10.11 GND+5V+5VSB+12VDC RETURN 12.13+12V+12VDC OUTPUT Note:CON2-XH CONNEETION,TYPE:pitc
37、h2.5mm Table 18 Pin-CON1 Connection And Function Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 10 of 11Page 10 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T NO.Pin Connection Function AC-L AC INPUT LINE -NC AC-N AC INPUT NUTUR
38、E Note:CON1-VH CONNEETION,TYPE:pitch3.96mm 9.Power Supply Mounting（安装尺寸）&Pin Connectio Document No.：Issued Date:2011-06-21 版权属于麦格米特,禁止任何未经授权的使用。Page 11 of 11Page 11 of 11 The copyright belongs to Megmeet.Any unauthorized use is prohibited.Specification Model：MP128FL-T Mount Method(装配注意事项)(装配注意事项)Tab
39、le 19 Note:1*.Mount the unit to the mounting board using M3 screw.The maximum value of the tightening torque is 0.4N-M.The insertion depth of the screw should be less 5.5mm.2*.Add 290mm190mm 0.25mm(W*-H*T)Mylar under PCB bottom.10.Package 包装包装 防静电气泡袋尺寸:330mm*215mm 包装箱尺寸：485mm*435mm*305mm D 5.5mm(1*)3.0mm H 6.0mm(2*)H1 11mm HD PCB SPS UNIT 286mm Nature wind TOP BOTTOM H1