《方形保险丝规格书.doc》由会员分享，可在线阅读，更多相关《方形保险丝规格书.doc（7页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、东莞市宏大电子有限公司广东省东莞市厚街镇大塘工业区DONG GUAN HONG DA ELECTRONIC TECHNOLOGY CO.,LTD 电话：0769-28672621 13434015353 CHEVRON传真：0769-89187292EMAIL:and127产品规格承认书宏大电子限公司HONG DA ELECTRONIC TECHNOLOGY CO.,LTD客户资料CUSTOMERS INFORMATION产品名称：PRODUCTION NAME塑封方形FUSE客户：CUSTOMER： 产品型号：PRODCTION TYPE:SET机型：MODEL NO：产品规格：PRODUC
2、T SPECIFICATIONST1A250V料号：PART NO:产品摘要：TYPE：特殊要求：SPECIAL REQUIREMENTS送样日期：DATE:承办人：ISSUEDER: 设计（DESIGN): 李雪梅 审核（CHECKED): 批准（APPROVDE): 客户确认APPROVDE BY签名： 日期：SIGN: DATE:结论（RESULT）：确认后请回传 PLEASE RETURN BY ONE COPY SET系列(慢断)保险丝规格书1. 适用范围:本产品为慢断微型塑料保险丝，适用于各类在250V以下电压电子电器元件内的电路中起过电流保护作用The fuse is a Tim
3、e-Lag micro plastic fuse , for the electronic device which rated voltageis less than AC 250V.2. 形状，外观及尺寸如下图(单位:mm) The out view, construction and dimensions to the following figure.（Unit:mm） 序号NO.部品名Parts Name材料Material数量Quantity可熔体Fuse Element合金线Alloy Wire1内芯core尼龙Nylon PA661外壳case尼龙Nylon PA661引线Le
4、ad Wire镀锡铜线Tin plated Copper Wire23.产品标志(Marking)3.1 保险丝上的标志应易于看清。The relevant markings shall be marked on the caps of the fuse and shall be easily visible. SET T1A250V 3.2保险丝上必须有下列标示：The markings for every fuse shall be prescribed as below according to the types.1) 安规认证标示（Safety Approval Logo）： 2)
5、额定电流（Rated Current）：1A3) 额定电压（Rated Voltage）：250V4) 商标（Trademark）：5) 特性符号（Characteristic Symbol）:T注意：本产品对标示的大小和位置没有规定Note：This product to sign the size and position of no provisions4.外观与形状(Appearance and shape) 4.1外观(Shape)外观不应有显著的污点,铁锈或裂纹且标示应很容易辨认的.Appearance should not stain, rust or cracks and ma
6、rked should be easily recognizable4.2形状(Appearance)微型保险丝(Micro Fuse)5机械特性( Mechanical Performances)保险丝应能承受下列二项试验。Fuse shall withstand the following two tests.5.1 拉力试验(Tensile Test)将保险丝保持在一个固定的位置，沿引线方向施加10N的拉力，引线、方形塑料帽不能松动并且方形塑料帽不应破裂。When fuse is fixed and the tensile force 10N is applied in a direct
7、ion to lead, no looseness of leads and square thermoplastic cap or damage of square thermoplastic cap shall occur.5.2 推力试验(Thrust Test)将保险丝保持在一个固定的位置，沿引线方向旋加2N的推力，引线、方形塑料不能松动并且方形塑料不应破裂。When fuse is fixed and the thrust 2N is applied in a direction to lead, no looseness of leads and square thermoplas
8、tic cap or damage of square thermoplastic cap shall occur. 6.电气特性（Electrical Characteristic）6.1实验条件(Test Condition)所有测试环境温度25+5,测试期间室内温度变化不得超过5All the test environment temperature of 25 +5 during the test the indoor temperature must not exceed 56.2 负载能力(Load Capacity)在通过150%的额定电流1小时保险丝不能熔断,通电实验中保险丝连
9、接处不能融化,保险丝外壳不能有烧焦,破裂现象.A current 150% Rated Current is then passed through the fuse-link for 1hour, Power experiments, the fuse junction can not melt, fuse housing can not be burnt, rupture phenomenon. 6.3平均I-T特性曲线图(供参考) The AVERAGE I-t Characteristics Curve(For referenge only) 6.4 熔断时间/电流特性Fusing T
10、ime-Current Characteristics 额定电流Rated Current熔断时间Disconnection time150%1 Hour Min （大于1小时）210%120 sec Max （小于120秒）275%0.410s（0.4到10秒）400%0.153s（0.15到3秒）1000%0.020.15s（0.02到0.15秒）7. 电压降（Voltage Drop）熔断体在额定电流条件下,两端的电压降不应超过下表规定的最大值。The voltage drop across the fuse-link at their rated current shall not e
11、xceed the maximum values is in follows.额定电流Rated Current额定电压Rated Voltage最大电压降Maximum Voltage Drop(mV)最大维持功耗Maximum Sustained Power Dissipation (mW)100mA250V350170125mA300180160mA280190200mA260200250mA240220315mA220250400mA200280500mA190310630mA180360800mA1604301A1405001.25A1306001.6A1207302A1008702
12、.5A10010003.15A10012004A10014005A10016806.3A10020008A10A8. 温度上升（Temperature Rise） 在150%额定电流条件下，通电15min后，将电流以每15min增加10%，直到保险丝断线，保险丝各部位温度不超过135 Power after 15min in 150% of rated current conditions, the current per 15min 10%, until the fuse blows, the fuse various parts of the temperature does not ex
13、ceed 135 9.耐久性试验/ ENDURANCE TEST耐久性试验过程（The process of endurance test is as follows.）1）对熔断体通过1倍的额定电流1小时，然后切断电流15分钟，重复此循环100 次。 current 1.0In is passed through the fuse-link for a period of 1hour. The current is then switched off for a period of 15 minutes. The cycle is repeated 100 times.2）然后对熔断体通以1
14、.5倍额定电流1小时；并测量两端电压降，计算其最大功耗不能超过上表所规定的最大值。 Fuse through to 1.5 times the rated current of 1 hour; and measure the voltage drop across, to calculate the maximum power consumption can not exceed the above table under the maximum3） 测量熔断体两端的电压降,且电压降的增大量不大于试验前测得值的10%。 Measuring both ends of the fuse volta
15、ge drop, and a large number of the increased voltage drop is not greater than 10% of the measured value before the test.4） 试验后,标记仍应清晰可辨，而且诸如端帽上的焊点不应出现任何明显的劣变。 After the test, the marking shall still be legible and soldered joints on end caps, for example, shall not show and appreciable deterioration
16、.10.分断能力（Breaking Capacity）额定分断能力为: 35A或10In(A.C.), 取其中较大者。保险丝分断电路后，方形塑料帽不应飞脱、损坏。Rated breaking capacity is 35A or 10In whichever is greater, tested with A.C. And after this test, there shall be not damaged or shattered of the square thermoplastic cap.11. 焊接参数（Soldering Parameters）1) 波峰焊接（ Wave sold
17、ering）: 260, 10sec. Max.2) 手工焊接（Manual soldering）: 300, 3sec. Max.12.保存条件温度(Temperature): +1060湿度(Humidity):相对温度75%下平均可以存放3年 Average relative temperature 75% can be stored for 3 years在非露天的情况下,相对湿度为95%,最多可存放30天.In the case of non-open, the relative humidity of 95%, can store up to 30 days13. 包装要求(Pac
18、king Details)13.1包装方式(Packing Mode)1) 散装（Bulk）：1000个/小袋 1000pcs/little plastic-bag 2) 盒装（Boxed）：1000个/盒，10小盒/大盒 1000pcs/box,10 little boxes/big box13.2所有产品的包装应能达到防潮、抗振的作用，以防在运输或贮存过程中产品受潮或损坏Packing should meet the requirements of anti-moisture and anti-shaking so that the products will not absorb moisture or be damaged during transportation or storage. 7