《AM-800600M3TNQW-00H规格书.pdf》由会员分享，可在线阅读，更多相关《AM-800600M3TNQW-00H规格书.pdf（25页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、 Date:2010/07/08 AMPIRE CO.,LTD.1 SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO.AMPIRE PART NO.AM-800600M3TNQW-00HAPPROVED BY DATE?Approved For Specifications?Approved For Specifications&Sample APPROVED BY CHECKED BY ORGANIZED BY AMPIRE CO.,LTD.2F.,No.88,Sec.1,Sintai 5th Rd.,Sijhih City,Ta
2、ipei County 221,Taiwan(R.O.C.)台縣汐止市新台五一段台縣汐止市新台五一段 88 號號 2(東方科學園區東方科學園區 D 棟棟)Date:2010/07/08 AMPIRE CO.,LTD.2 RECORD OF REVISION Revision Date Page Contents Editor2010/07/08 -New Release Eric Date:2010/07/08 AMPIRE CO.,LTD.3 1.INSTRUCTION Ampire 8.4”Display Module is a color active matrix TFT-LCD th
3、at uses amorphous silicon TFT as a switching device.This model is composed of a TFT-LCD panel,a driving circuit.This TFT-LCD has a high resolution(800(R.G.B)X 600)and can display up to 262,144 colors.1.1 Features(1)Construction:a-Si TFT-LCD with driving system,White LED Backlight.(2)LCD type:Transmi
4、ssive,Normally White(3)Number of the Colors:(a)262K colors(LVDS 6 bits mode)(default)(b)16.2M colors(LVDS 8 bits mode).(4)LVDS Interface(Default setting:6 bit mode).(5)LCD Power Supply Voltage:3.3V single power input,built-in power supply circuit.(6)Build-in LED Driver IC(VLED=12V).(7)ROHS compliant
5、.2.PHYSICAL SPECIFICATIONS Item Specifications unit Display resolution(dot)800RGB(W)x 600(H)dots Active area 170.40(W)x 127.80(H)mm Pixel pitch 213(W)x 213(H)um Color configuration R.G.B-stripe Overall dimension 203.0(W)x 145.5(H)x 8.0(D)mm Weight 280 g Backlight unit LED Display color 262K(default)
6、colors If user wants to change the default setting for mass production,please contact with Ampire.Well apply a new P/N for you.Ruixian Electronics agent and sell this model panel.Date:2010/07/08 AMPIRE CO.,LTD.4 3.ABSOLUTE MAXIMUM RATINGS Item SymbolMin.Max.Unit NoteSupply voltage range VCC-0.3 4 V(
7、1)Voltage range at any terminal VI-0.3 VCC+0.3V Operating Temperature Top-20 70 Storage Temperature Tstg-30 80 Note:All voltage values are with respect to the GND terminals unless otherwise noted.4.OPTICAL CHARACTERISTICS Item Symbol Condition Min.Typ.Max.UnitNote Response Time Tr+Tf-8 16 ms(1)Contr
8、ast ratio CR=0 480 600-(2)(3)L 65 75-Horizontal R 65 75-U 50 60-Viewing Angle Vertical D CR10 60 70-Deg.(5)Luminance(Center)L 280 350-cd/m2(3)(4)IL=52mA Ta=25 Luminance Uniformity L-70-%(3)(4)Wx 0.26 0.31 0.367 Color chromaticity White Wy=0 0.28 0.33 0.38 NOTE:These items are measured by BM-5A(TOPCO
9、N)or CA-1000(MINOLTA)in the dark room(no ambient light)(1)Definition of Response Time(White-Black)Date:2010/07/08 AMPIRE CO.,LTD.5 (2)Definition of Contrast Ratio Measure contrast ratio on the below 5 points(refer to figurel,#1#5point)and take the average value Contrast ratio is calculated with the
10、following formula:Contrast Ratio(CR)=(White)Luminance of ON (Black)Luminance of OFF (3)Definition of Luminance:Measure white luminance on the center point(point 5)and take the value.(4)Definition of Luminance Uniformity:Measured Maximum luminanceL(MAX)and Minimum luminanceL(MIN)on the 5 points Lumin
11、ance Uniformity is calculated with the following formula:L=L(MIN)/L(MAX)X 100%(5)Definition of Viewing Angle Date:2010/07/08 AMPIRE CO.,LTD.6 5.ELECTRICAL CHARACTERISTICS 5.1 Power Specification Item SymbolMin.Typ.Max.Unit NoteLogic/LCD Drive Voltage VCC 3.0 3.3 3.6 V VCC Current ICC 120 mA(1)Note1:
12、fV=60Hz,Ta=25,Display pattern:All Black 5.2 LVDS electrical Specification Date:2010/07/08 AMPIRE CO.,LTD.7 6.BACKLIGHT UNIT Item Symbol Min.Typ.Max.Unit Note Input Voltage VLED 10.8 12.0 12.6 V Input Current ILED-210-mA 100%PWM dutyDimming Frequency Fpwm 200 30K Hz Dimming Voltage High 2-5.0 V Dimmi
13、ng Voltage Low 0-0.8 V LED Forward Current IF-52 60 mA Ta=25 LED Forward Voltage VF 38.4 43.8 V IF=52mA,Ta=25 LED life time 50,000-Hr IF=52mA,Ta=25 Note 1:Ta means ambient temperature of TFT-LCD module.Note 2:VLED,ILED are defined for LED B/L.(100%duty of PWM dimming)Note 3:IF,VF,Fpwm are defined fo
14、r LED Driver.Note 4:If the module is driven by high current or at high ambient temperature&humidity condition.The operating life will be reduced.Note 5:Operating life means brightness goes down to 50%minimum brightness.LED life time is estimated data.Note 6:the structure of LED B/L shows as below.Da
15、te:2010/07/08 AMPIRE CO.,LTD.8 6.1 PWM Dimming Control 7.INTERFACE 7.1 Interface Definition CN1:LVDS Connector Pin no Symbol Function 1 VCC POWER SUPPLY:3.3V 2 VCC POWER SUPPLY:3.3V 3 UD Vertical Reverse Scan Control.4 LR Horizontal Reverse Scan Control.5 RXIN1-Transmission Data of Pixels 1 6 RXIN1+
16、Transmission Data of Pixels 1 7 GND Power Ground 8 RXIN2-Transmission Data of Pixels 2 9 RXIN2+Transmission Data of Pixels 2 10 GND Power Ground 11 RXIN3-Transmission Data of Pixels 3 12 RXIN3+Transmission Data of Pixels 3 13 GND Power Ground 14 RXCKIN-Sampling Clock 15 RXCKIN+Sampling Clock 16 GND
17、Power Ground 17 NC No connection 18 NC No connection 19 NC LVDS 6 bits mode:No connection(default)LVDS 8 bit mode:(RXIN4-)Transmission Data of Pixels 4 20 NC LVDS 6 bits mode:No connection(default)LVDS 8 bit mode:(RXIN4+)Transmission Data of Pixels 4 Date:2010/07/08 AMPIRE CO.,LTD.9 8 bits LVDS inpu
18、t R0R1R2R3R4R5B0B1B2B3B4B5G0G1G2G3G4G5VSHSDERxIN1RxIN2RxIN3R6R7G6G7B7B6RSVRxIN4RxCLKIN Note:R/G/B data 7:MSB,R/G/B data 0:LSB Signal Name Description Remark R7 R6 R5 R4 R3 R2 R1 R0 Red Data 7(MSB)Red Data 6 Red Data 5 Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0(LSB)Red-pixel Data Each red
19、 pixels brightness data consists of these 8 bits pixel data.G7 G6 G5 G4 G3 G2 G1 G0 Green Date 7(MSB)Green Date 6 Green Date 5 Green Date 4 Green Date 3 Green Date 2 Green Date 1 Green Date 0(LSB)Green-pixel Data Each green pixels brightness data consists of these 8 bits pixel data.B7 B6 B5 B4 B3 B2
20、 B1 B0 Blue Data 7(MSB)Blue Data 6 Blue Data 5 Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0(LSB)Blue-pixel Data Each blue pixels brightness data consists of these 8 bits pixel data.RxCLKIN+RxCLKIN-LVDS Clock Input DE Display Enable VS Vertical Sync HS Horizontal Sync Date:2010/07/08 A
21、MPIRE CO.,LTD.10 6 bits LVDS input R0R1R2R3R4R5B0B1B2B3B4B5G0G1G2G3G4G5VSHSDERxIN1RxIN2RxIN3RxCLKIN Note:R/G/B data 5:MSB,R/G/B data 0:LSB Signal Name Description Remark R5 R4 R3 R2 R1 R0 Red Data 5(MSB)Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0(LSB)Red-pixel Data Each red pixels brightn
22、ess data consists of these 6 bits pixel data.G5 G4 G3 G2 G1 G0 Green Date 5(MSB)Green Date 4 Green Date 3 Green Date 2 Green Date 1 Green Date 0(LSB)Green-pixel Data Each green pixels brightness data consists of these 6 bits pixel data.B5 B4 B3 B2 B1 B0 Blue Data 5(MSB)Blue Data 4 Blue Data 3 Blue D
23、ata 2 Blue Data 1 Blue Data 0(LSB)Blue-pixel Data Each blue pixels brightness data consists of these 6 bits pixel data.RxCLKIN+RxCLKIN-LVDS Clock Input DE Display Enable VS Vertical Sync HS Horizontal Sync Date:2010/07/08 AMPIRE CO.,LTD.11 Setting of scan control input UD LR Scanning direction GND G
24、ND Up to Down,Left to Right VCC VCC Down to Up,Right to Left GND VCC Up to Down,Right to Left VCC GND Down to Up,Left to Right CN2:LED Driver Connector Pin no Symbol Function 1 VLED 12V input 2 GND GND 3 Display_ON/OFF +3.3V:ON,0V:OFF 4 Dimming PWM Date:2010/07/08 AMPIRE CO.,LTD.12 7.2 Block Diagram
25、 TFT-LCD800 x(3)x 600PixelsSource Driver ICWith T-conLVDSReceiverDC/DCConverterGammerCorrectionGenerationCircuitLVDSDCPowerConnector 2DCPowerLED Driver 8.AC Timing characteristic 8.1 AC Timing characteristic of LVDS Date:2010/07/08 AMPIRE CO.,LTD.13 Date:2010/07/08 AMPIRE CO.,LTD.14 8.2 AC Timing ch
26、aracteristic of Panel Date:2010/07/08 AMPIRE CO.,LTD.15 Date:2010/07/08 AMPIRE CO.,LTD.16 8.3 Power ON/OFF Sequence VALIDDATA90%90%10%10%T1T2T3T4T5T6T7Power Supply VDDLVDS SignalBacklight On10%10%8.3.1 Power ON/OFF sequence timing Value Symbol Min.Typ.Max.Unit T1 0.5-20 ms T2 0 40 50 ms T3 200-ms T4
27、 200-ms T5 0 40 50 ms T6 0-20 ms T7 1000-ms Date:2010/07/08 AMPIRE CO.,LTD.17 9.QUALITY AND RELIABILITY 9.1 TEST CONDITIONS Tests should be conducted under the following conditions:Ambient temperature :25 5C Humidity :60 25%RH.9.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105
28、E,level II,normal single sampling plan.9.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose.A minor defect is one that does not materially reduce the usability of the unit for its intended pu
29、rpose or is an infringement from established standards and has no significant bearing on its effective use or operation.9.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under florescent light.The inspection area of LCD panel sha
30、ll be within the range of following limits.Date:2010/07/08 AMPIRE CO.,LTD.18 9.5 INCOMING INSPECTION STANDARD FOR TFT-LCD PANEL DEFECT TYPE LIMIT Note0.15mm Ignore 0.15mm0.5mm N4 SPOT 0.5mm N=0 Note10.03mmW0.1mm,L5mm N3 FIBER 1.0mmW,1.5mmL N=0 Note10.15mm Ignore 0.15mm0.5mm N2 POLARIZER BUBBLE 0.5mm
31、 N=0 Note1VISUAL DEFECT INTERNAL Mura It OK if mura is slight visible through 6%ND filter C Area O Area Total Note3BRIGHT DOT N0 N2 N2 Note2DARK DOT N2 N4 N4 TOTAL DOT N4 Note2TWO ADJACENT DOT N0 N0 N0 Note4THREE OR MORE ADJACENT DOT NOT ALLOWED ELECTRICAL DEFECT LINE DEFECT NOT ALLOWED (1)One pixel
32、 consists of 3 sub-pixels,including R,G,and B dot.(Sub-pixel=Dot)(2)LITTLE BRIGHT DOT ACCEPTABLE UNDER 6%ND-Filter Note1 W:Widthmm,L:Lengthmm,N:Number,:Average Diameter Date:2010/07/08 AMPIRE CO.,LTD.19 Note2 Bright dot is defined through 6%transmission ND Filter as following.Note3 C Area:Center of
33、display area O Area:Outer of display area Note4 Judge defect dot and adjacent dot as following.Allow below(as A,B,C and D status)adjacent defect dots,including bright and dart adjacent dot.And they will be counted 2 defect dots in total quantity.(1)The defects that are not defined above and consider
34、ed to be problem shall be reviewed and discussed by both parties.(2)Defects on the Black Matrix,out of Display area,are not considered as a defect or counted.Date:2010/07/08 AMPIRE CO.,LTD.20 9.6 Reliability Test Test Item Test Conditions NoteHigh Temperature Operation 703C,t=96 hrs Low Temperature
35、Operation-203C,t=96 hrs High Temperature Storage 803C,t=96 hrs 1,2 Low Temperature Storage-303C,t=96 hrs 1,2 Thermal Shock Test-20C 25C 70C 30 m in.5 min.30 min.(1 cycle)Total 5 cycle 1,2 Humidity Test 60 C,Humidity 90%,96 hrs 1,2 Vibration Test(Packing)Sweep frequency:10 55 10 Hz/1min Amplitude:0.7
36、5mm Test direction:X.Y.Z/3 axis Duration:30min/each axis 2 Note 1:Condensation of water is not permitted on the module.Note 2:The module should be inspected after 1 hour storage in normal conditions (15-35C,45-65%RH).Definitions of life end point:?Current drain should be smaller than the specific va
37、lue.?Function of the module should be maintained.?Appearance and display quality should not have degraded noticeably.?Contrast ratio should be greater than 50%of the initial value.Date:2010/07/08 AMPIRE CO.,LTD.21 10.USE PRECAUTIONS 10.1 Handling precautions 1)The polarizing plate may break easily s
38、o be careful when handling it.Do not touch,press or rub it with a hard-material tool like tweezers.2)Do not touch the polarizing plate surface with bare hands so as not to make it dirty.If the surface or other related part of the polarizing plate is dirty,soak a soft cotton cloth or chamois leather
39、in benzine and wipe off with it.Do not use chemical liquids such as acetone,toluene and isopropyl alcohol.Failure to do so may bring chemical reaction phenomena and deteriorations.3)Remove any spit or water immediately.If it is left for hours,the suffered part may deform or decolorize.4)If the LCD e
40、lement breaks and any LC stuff leaks,do not suck or lick it.Also if LC stuff is stuck on your skin or clothing,wash thoroughly with soap and water immediately.10.2 Installing precautions 1)The PCB has many ICs that may be damaged easily by static electricity.To prevent breaking by static electricity
41、 from the human body and clothing,earth the human body properly using the high resistance and discharge static electricity during the operation.In this case,however,the resistance value should be approx.1M and the resistance should be placed near the human body rather than the ground surface.When th
42、e indoor space is dry,static electricity may occur easily so be careful.We recommend the indoor space should be kept with humidity of 60%or more.When a soldering iron or other similar tool is used for assembly,be sure to earth it.2)When installing the module and ICs,do not bend or twist them.Failure
43、 to do so may crack LC element and cause circuit failure.3)To protect LC element,especially polarizing plate,use a transparent protective plate(e.g.,acrylic plate,glass etc)for the product case.4)Do not use an adhesive like a both-side adhesive tape to make LCD surface(polarizing plate)and product c
44、ase stick together.Failure to do so may cause the polarizing plate to peel off.Date:2010/07/08 AMPIRE CO.,LTD.22 10.3 Storage precautions 1)Avoid a high temperature and humidity area.Keep the temperature between 0C and 35C and also the humidity under 60%.2)Choose the dark spaces where the product is
45、 not exposed to direct sunlight or fluorescent light.3)Store the products as they are put in the boxes provided from us or in the same conditions as we recommend.10.4 Operating precautions 1)Do not boost the applied drive voltage abnormally.Failure to do so may break ICs.When applying power voltage,
46、check the electrical features beforehand and be careful.Always turn off the power to the LC module controller before removing or inserting the LC module input connector.If the input connector is removed or inserted while the power is turned on,the LC module internal circuit may break.2)The display r
47、esponse may be late if the operating temperature is under the normal standard,and the display may be out of order if it is above the normal standard.But this is not a failure;this will be restored if it is within the normal standard.3)The LCD contrast varies depending on the visual angle,ambient tem
48、perature,power voltage etc.Obtain the optimum contrast by adjusting the LC dive voltage.4)When carrying out the test,do not take the module out of the low-temperature space suddenly.Failure to do so will cause the module condensing,leading to malfunctions.5)Make certain that each signal noise level
49、is within the standard(L level:0.2Vdd or less and H level:0.8Vdd or more)even if the module has functioned properly.If it is beyond the standard,the module may often malfunction.In addition,always connect the module when making noise level measurements.6)The CMOS ICs are incorporated in the module a
50、nd the pull-up and pull-down function is not adopted for the input so avoid putting the input signal open while the power is ON.7)The characteristic of the semiconductor element changes when it is exposed to light emissions,therefore ICs on the LCD may malfunction if they receive light emissions.To