《回流炉后品质不良术语.doc》由会员分享，可在线阅读，更多相关《回流炉后品质不良术语.doc（4页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、德信诚培训网回流炉后品质不良术语 SKIP PRINTING:漏印 SOLDER:焊锡 SOLDER ABILITY:可焊性 SOLDER BALL:锡球 SOLDER BRIDGE:锡桥 SOLDER SIDE:焊锡面 SUBSTRATE:底材 CREAK:裂痕 CREASE:皱褶 DESMEAR:除污 DEWETTING:缩锡 HOLE VOID:破洞 HOLE BREAKOUT:破孔 TOUCH UP:修理 TRACE:线路 印章错误：WRONG STAMPS 缺件:MISSING PARTS 脚未弯:PIN NOT BENT 序号错:WRONG S/N 错件：WRONG PARTS 缺
2、盖章：MISSING STAMP 断路:OPEN 尺寸错误：DIMENSION WRONG) 包装错误:WRONG PACKING 立碑:TOMBSTONE 多件:EXCESSIVE PARTS) 缺标签:MISSING LABEL 二极体坏:DIODE NG 短路:SHORT) 缺序号:MISSING S/N) 電晶体坏:TRANSISTOR NG 线短:WIRE SHORT 标签错:WRONG LABEL 管装错误:TUBES WRONG 线長:WIRE LONG 标示错:WRONG MARK 阻值错误:IMPEDANCE WRONG 拐线:WIRE POOR DDRESS 脚太短:PIN
3、 SHORT 版本错误:REV WRONG 冷焊:COLD SOLDER 電測不良:TEST FAILURE 金手指沾锡:SOLDER ON GOLDEN FINGERS 包焊:EXCESS SOLDER 锡凹陷:SOLDER SCOOPED 版本未标:NON REV LEBEL 空焊:MISSING SOLDER 线序错:W/L OF WIRE 包装损坏:PACKING DAMAGED 锡尖:SOLDER ICICLE 未測試:NO TEST 印章模糊:STAMPS DEFECTIVE 锡渣:SOLDER SPLASH VR变形:VR DEFORMED 标签歪斜:LABEL TILT 锡裂:
4、SODER CRACK PCB翹皮:PCB PEELING 外箱损坏:CARTON DAMAGED 锡洞:PIN HOLE PCB弯曲:PCB TWIST 点胶不良:POOR GLUE 零件沾胶:GLUE ON PARTS IC座氧化:SOCKET RUST 脚未剪:PIN NO CUT 零件脚長:PARTS PIN LONG 缺UL标签:MISSING UL LABEL 线材安装不良:WIRE UNSEATED 滑牙:SCREW LOOSE 浮件:PARTS LIFT 线材不良:WIRE FAILURE 氧化:RUST 零件歪斜:PARTS TILT 零件脚损坏:PIN DAMAGED 零件
5、相触 :PARTS TOUCH 脚未出:PIN UNVISIBLE 零件偏移:PARTS SHIFT 溢胶:EXCESSIVE GLUE 零件变形:PARTS DEFORMED 包装文件错:RACKING DOC WRONG 锡短路:SOLDER BRIDGE 零件损坏:PARTS DAMAGED 包装数量错:PACKING QTY WRONG 锡不足:SOLDER INSUFFICIENT 垫片安装不良:WASHER UNSEATED 零件未定位:PARTS UNSEATED 极性反:WRONG POLARITY 零件多装:PARTS EXCESS 金手指沾胶:GLUE ON GOLDEN FINGERS 脚未入:PIN UNSEATED 零件沾锡:SOLDER ON PARTS Skewing（歪斜） Wicking（焊料上吸） Bridging（桥连） Voiding（空洞） Opening（开路） Spattering（飞溅） Uneven Joint Height（焊点高度不均）更多免费资料下载请进：好好学习社区