《中英文对照工程术语表.xls》由会员分享，可在线阅读，更多相关《中英文对照工程术语表.xls（9页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、 英/中对照工程术语表Aapproval确认；批准angle角度allow允许acc./according依照；根据alloy合金Bboth两（边/面）both sides两面burr毛刺deburr去毛刺broken edge倒角external radii外部圆角chamfer倒角Cchecked审核change更改countersink打埋头孔；打沉孔code编码core型芯coarse粗糙的；要求低的Circularity圆度Cylindricity圆柱度Coaxiality同心（轴）度circular run-out圆跳动CT/Casting Tolerance压铸公差Ddesign
2、设计draft拔模斜度draft angle拔模角度Dept./department部门date日期data资料；数据（复数）datum基准；数据（单数）datum plane基准面detail局部视图；详细视图deep深dia./diameter直径Eedge棱边external外部的；表面的external thread外螺纹engineer工程ejector顶杆ring ejector推管EDM=Electron Discharge Machining放电加工Ffinish表面处理要求flatness平面度fine极好的；高的Ggeneral普通的；一般的；常规的Hhole孔Iident
3、ificationinternal内在的；国内的internal thread内螺纹Lline线linear线性linear dimension 线性尺寸Mmaterial材料；原料manufacture制造mould模具model模型metric公制measure测量machining margin机加工余量medium中等的Nnickel-plated镀镍层glide ground andnickel-platedacc.to N67F 85301.电镀的范围和镀镍层的厚度根据N67F853 01标准。Ooperation操作operator操作者Ppart name零件名称Part No
4、.零件号Part of产品（项目）名称Product产品Proofreader校对position位置point点Perpendicularity 垂直度per.按照；参照pin销钉Parallelism平行度porosity气孔Rrevision版本；版次Rev.版本；版次round沿周roughness粗糙度RMA/Required Machining Allowance 要求的机加工余量reasonable合理的，正当的Sscale比例sheet页次；表单standardization标准化specify指定unless otherwise specified,surface表面除非另有
5、指定，side一边；（另一边）slide滑块section剖面；剖视图sink下沉Symmetry对称度Tgeneral toerance 一般公差；未注公差Tol./tolerance公差tolerance for linear线性公差thread螺纹tolerance for angular角度公差treatment处理surface treatment 表面处理technical技术的torque扭矩；转矩tap螺纹孔；攻丝TYP.类似尺寸top顶端；顶面Uunspecified未注UNLESS OTHERWISE SPECIFIED未注VView视图Wweight重量without无w
6、all thickness壁厚ZZinc锌ALLIEDUNLESS OTHERWISE SPECIFIED:未注MININUM xxNm TORQUE AND XXKN TENSION TO PULL OFF THE STUD螺栓应能承受XXNm扭矩和XXKN拉力不松脱SUPPLIER ID,CAVITY#,AND DATE CODE ON THIS SURFACE此面标记供应商代码，型腔号和日期CORROSION PROTECTION OF STUD PER BMW GS 9001D ZNS3螺栓的防腐蚀性能应符合宝马GS 9001D ZNS3标准MAXIMUM POROSITY SIZE
7、xmm3 INSIDE THE PART,NO POROSITY PERMITTED FROM SURFACETO xmm INSIDE,POROSITY NOT TO EXCEED ASTM E505 LEVEL 3零件内部气孔不大于xmm3，表面xmm之内不允许有气孔，气孔标准按ASTM E505 不大于3级BURRS AND SHARP EDGES CONSISTENT WITH GOOD MFG,AND TOOLING PRACTICESPERMISSIBLE PROVIDED THEY DO NOT AFFECT THE ASSEMBLY,HANDING OR FUNCTION OF
8、 THEPART毛刺与锐边应以加工方式去除，不影响零件装配，手感和功能的地方允许模具直接成型BoschUNSPECIFIED DRAFT ANGLES x PER SIDE未注拔模斜度 单边1度INTERNAL DIMENSIONS ARE LOWER LIMITS AND EXTERNAL DIMENSIONS ARE UPPER LIMITS内部尺寸取下偏差，外部尺寸取上偏差UNSPECIFIED INSIDE RADII AND RIBS ON BOTTOM ROUNDED OFF WITH R=X未注内部圆角和筋位底部圆角为R=XUNSPECIFIED WALL THICKNESSES
9、 D=xx未注壁厚D=XXPARTING LINE FLASH NOT ALLOWED ;REMAIN OF SPRUE MAX.X CONVEX分型面不允许有飞边；浇口痕不大于X，要求凸起圆滑SEALING SURFACE AND VISIBLE SURFACE FREE OF PARTING PLANE-TOOL,EJECTORS,SHRINKMARKS，EXTRACTION BRUSH MARKS。LABELLING SURFACES:SEE MATERIAL SPECIFICATION密封面和外观面不应有分型线，顶针痕，缩痕，脱模痕迹。标记面参阅下列标记VISIBLE/FUNCTION
10、AL SURFACES外观面/功能面NO SHRINK MARKS AT VISIBLE SURFACES ALLOWED外观面不允许有缩痕PARTING PLANE分型面MOLD CAVITY NUMBER HAS TO BE SPECIFIED型腔数按指定DEBURR:AFTER CHOICE OF THE MANUFACTURER去毛刺工序：制造商决定TEST DIMENSIONS检测尺寸DIMENSIONS,MARKED WITH 10,20 AND 30,HAS TO BE AJUSTED WITH xxxxxx,THAT AMAXIMUM CLEARANCE APPEARS ABO
11、UT xmm作10，20和30标记的尺寸用于和XXXXXX配合时作调整，最大修整量 约 Xmmconvex glossy凸起圆滑ElectroluxREFER TO 3D CAD MODEL FOR ALL UNSPECIFIED DIMENSIONS未注尺寸参考3D图档GENERAL MATERIAL THICKNESS未注材料壁厚UNLESS OTHERWISE SPECIFIED DRAFT TO BE x MINIMUM RADIUS TO BE x未注拔模斜度X 最小圆角XGATE LOCATION TO BE APPROVE BEFORE TOOLING COMMENCES浇口位置
12、须经确认CAVITY NO.TO BE POSITIONED IN DESIGNATED AREA型腔号须标记在制定位置TOOL DESIGN TO BE APPROVED BY ELECTROLUX ENGINEERING DEPARTMENT AND MOULDER FORALL TRAILS模具设计须经依莱克斯工程部门确认，模具负责人参与全过程SAMPLES TO BE APPROVED BY ELECTROLUX ENGINEERING DEPARTMENT BEFORE PRODUCTIONCOMMENCES产品正式投产前，须经依莱克斯工程部门确认样品PART TO BE FREE
13、OF FLASH产品不允许毛刺PARTS SHALL BE PACKED IN SUCH A MANNER AS TO PREVENT DAMAGE IN TRANSIT ORSTORAGE产品须按指定要求包装以避免在运输和储存过程中损坏VISUAL INSPECTION ON CASTING POROSITY MUST BE PERFORMED ON CROSS SECTIONINDICATED BY DOTTED LINES.INSPECTION TO BE PERFORMED ON MINIMUM OF 1 SAMPLEFROM EACH CAVITY EVERY 4 HOURS必须按虚
14、线指定的零件的横面进行铸孔的目测检验。检验频度：每小时每腔最少一件FAILURE TESTING TO BE CONDUCTED ON MINIMUM OF 1 SAMPLE FROM EACH CAVITY,AS PERELECTROLUX SPEC T110574,ON AN HOURLY BASIS.失效测试按依莱克斯T110574规范执行，每隔一小时每腔最少一件NO CHANGE TO APPROVED MATERIAL SPECIFICATION,COMPONENTS,PROCESSES OR SOURCE OFMANUFACTURE SHALL BE MADE,UNLESS PRI
15、OR SAMPLES ARE PROVIDED AND APPROVED BYELECTROLUX HOME PRODUCTS PTY LTD,REFRIGERATION PLANT ORANGE.在依莱克斯“ORANGE”制冷厂确认新的样件前，已确认的物料规格，部件，流程或现有供应商不允许更改ALL MOULD MARKS TO BE APPROVED BY ENGINEERING DEPT.BEFORE PRODUCTION COMMENCES产品正式投产前，所有模痕须经依莱克斯工程部门确认REMOVE ALL FLASH须去除所有毛刺GATE TO BE POSITIONED IN DE
16、SIGNATED AREA ONLY浇口须设定在制定位置CAVITY NO.TO BE POSITIONED IN DESIGNATED AREA ONLY型腔号须标记在制定位置HUSQVARNABASIC DESIGN ACC.TO THE 3D-MODEL IN CATIA基本设计以CATIA的3D文档为依据LOCATION OF GATINGS MUST BE APPROVED BY DESIGN DEPARTMENT浇口位置须经设计部门确认REVISION LETTER,CHANGEABLE本版号：可变MARKING:MARK HEIGHT x mm,RAISED x mm标记字高x
17、mm，字凸x mmBURRS:HEIGHT MAX x mm,THICKNESS MAX x mm最大飞边高度x mm,厚度x mmUNLESS OTHERWISE SPECIFIED:RADIUS R x未注圆角R xLOCATION OF EJECTOR PINS IS MARKED WITH x AND x标记X 和X的为顶针位置DIE CASTING产品压铸成型FIXED REST SURFACES FOR MACHING ARE U1,U2 U3,Z AT U1,U2,U3 IS THE DISTANCE TOMACHINED PLANE B.S1,S2 AND S3 IS AT T
18、HE OPPOSITE SIDE OF U1,U2 AND U3.机加工装夹位置U1,U2 U3,对应的Z值是U1,U2,U3至机加工面B的距离。S1,S2 ANDS3是U1,U2 AND U3的相对面。CONTROL AND CAPABILITY FEATURES.THERE ARE x FEATURES ON THIS DRAWING.生产加工能力控制标记符号，此图共有x处machining margin机加工余量NEWELLLEFT HANDED PART IS DETAILED图纸所示为左半部件DIMS TAKEN AT THEORETICAL INTERSECTION尺寸标注为零件理论交点尺寸ANY UNSPECIFIED DIMENSIONS WILL BE CONTROLLED BY THE TOOLING MODEL未注尺寸由模具尺寸保证PRINT DIMENSIONS ARE FOR RAW CASTINGS图纸尺寸为铸造毛坯尺寸CAVITY I.D.,PART NUMBER,AND VENDOR NUMBER REQUIRED产品上须标记型腔号，产品编号和供应商代码NO MORE THAN.004 MISMATCH/FLASH.分型错位和飞边不允许超过0.004BREAK ALL SHARP EDGES不允许有锐边