汽车专业英语词汇大全.doc

《汽车专业英语词汇大全.doc》由会员分享，可在线阅读，更多相关《汽车专业英语词汇大全.doc（22页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。

1、汽车专业英语词汇大全中文 English轮椅升降机 wheel chair lift图例 legend工位 station吊运装置 overhead hoist更衣室 restroom1号厂房工艺布置方案图 proposal of the Plant I layout合笼 mate底盘平移台 chassis shuttle车辆转移台 bus transfer前围角板 front wall angle cover后围侧板 rear wall side cover保险杠 bumper三类底盘 three type chassis左侧围应力蒙皮 R/S stretching skin (road s

2、ide)中涂 floating coat拼装台 collector切割轮口 wheel -arch cutting内饰 trim线束 harness返工 re-doing轮罩护板 wheel house发车前准备 pre-delivery举升 hoist小批量产品 be pilot2 套 two kits配电站 power transformer substation裙板 skirt发动机托架 engine holding frame诊断报警系统 diagnosis and alarming system互换性 interchangeability缩微图纸 microfiche files总装

3、 final assembly磷化 phosphating仪表板 dash board切齐 trimming结构完整性 structure integrity自动愈合的防腐材料 self-healing corrosion preventative material长途客车 inter-city bus改装厂 refitting factory遮阳板 sun visor随车工具 tool box钢化玻璃 toughened grass异形钢管 special steel pipe全天候空调系统 full range A/C强制通风 ram-air ventilation停机时间 downtim

4、e无公害柴油 clean diesel宽敞悬臂式座椅 roomy cantilevered seat防滑地板 no-skid floor织物纹里铝合金 textured aluminum extrution爬坡能力 grade ability排水阀 drain valve除湿器 moisture ejector怠速时 at idle琴式驱动桥 banjo type drive axle通风口 duct恒温控制 thermostatic control平衡水箱 surge tank变光开关 simmer switch消音器 muffler防破坏 vandal resistant聚碳化透镜 pol

5、y-carbonate len镀锌板 galvanized plate搭接 lap亮丽的外表 smart apperance隐藏式固定 concealed fastening水洼 ponding发动机中置式客车 bus with under floor engine组合式客车车身 modular bus body薄壳式结构 shell construction衬垫 pad空气导流板 air deflector搁梁 shelf beam腰梁 waist rail梭梁 stabilizing beam腰带式安全带 diagonal safety belt压条 trim strip嵌条 insert

6、ion strip翼板 fender斜撑 bracing piece转向盘回正性试验 test of steering wheel returnability转向盘转角脉冲试验 steering wheel impulse input test转向盘转角阶跃输入试验 steering wheel step input or transient state yaw response test极限侧向加速度试验 limiting lateral acceleration test汽车平顺性随机输入行驶试验 automobile ride random input running test汽车平顺性

7、单脉冲输入行驶试验 automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验 measurement of natural frequency and damping raito of suspension功率突然变化影响试验 test of effect of sudden power change 收油门后控制试验 test of control at breakway横风稳定性试验 test of crosswind stability反冲试验 kick-back test轮胎爆破响应时间试验 test of b

8、urst response of tyre绕过障碍物试验 obstacle avoidance test移线试验 lane change testJ型转弯试验 test of J turn频率响应时间试验 frequency response test瞬态响应时间试验 transient response test阶路响应时间试验 step response test脉冲响应试验 pulse response test静态操舵力试验 static steering effort test悬架举升试验 jack-up test of suspension耐翻倾试验 test of overtur

9、ning immunity轮辋错动试验 rim slip test风洞试验 wind tunnel test制动稳定性试验 test of braking stability最小转弯直径试验 minimum turning diameter test操舵力试验 steering effort test类型 type发动机 engine内燃机 intenal combusiton engine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发

10、动机 compression ignition engine往复式内燃机 reciprocating internal combustion engine化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 superch

11、arged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机 water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 mul

12、tiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engi

13、ne中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead camshaft engineV形发动机 V-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多

14、气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical engineW形发动机 w-engineI形发动机 I-engineL形发动机 L-engineF形发动机 F-engine性能 performance二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压

15、循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程 expansion-exchange

16、 stroke换气压缩行程 exchange-compression stroke 止点 dead center 上止点 top dead center(upper dead center) 下止点 lower dead center(bottom dead center) 上止点前 budc(before upper dead center) 上止点后 atdc(after top dead cetner) 下止点前 bbdc(before bottom dead center) 下止点后 abdc(after bottom dead center) 缸径 cylinder bore 缸径与

17、行程 bore and stroke 空气室 energy chamber 气缸余隙容积 cylinder clearance volume 燃烧室容积 combustion chamber volume 气缸最大容积 maximum cylinder volume 压缩室 compression chamber 排气量 displacement 发动机排量 engine displacement 活塞排量 piston swept volume 气缸容量 cylinder capacity 单室容量 single-chamber capacity 容积法 volumetry 压缩比 comp

18、ression ratio 临界压缩比 critical compression ratio 膨胀比 expansion ratio 面容比 surface to volume ratio 行程缸径比 stroke-bore ratio 混合比 mixture ratio 压缩压力 compression pressure 制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio 燃空比 fuel air ratio 燃料当量比 fuel equivalence ratio 扭矩 torque 单缸功率 power per

19、cylinder 升功率 power per liter 升扭矩 torque per liter 升质量 mass per liter 减额功率 derating power 输出马力 shaft horsepower 马力小时，马力时 horsepower-hour 总马力 gross horse power 总功率 gross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consumption 空气消耗率 air consumption 机油消耗量 oil consumption 有效马力 net hor

20、se power 额定马力 rated horse power 马力重量系数 horsepower-weight factor 制动功率 brake horse power 制动热效率 brake thermal efficiency 总效率 overall efficiency 排烟极限功率 smoke limiting horsepower 功率曲线 power curve 机械损失 mechanical loss 机械效率 mechanical efficiency 有效热效率 effective thermal efficiency 充气系数 volumetric efficiency

21、 过量空气系数 coefficient of excess air 适应性系数 adaptive coefficient 扭矩适应性系数 coefficient of torque adaptibility 转速适应性系数 speed adaptive coefficient 强化系数 coefficient of intensification 校正系数 correction factor 换算系数 conversion factor 活塞平均速度 mean piston speed 发动机转速 engine speed (rotational frequency) 怠速转速 idling

22、speed 经济转速 economic speed 起动转速 starting speed 最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque 最高空转转速 maximum no load governed speed 调速 speed governing 超速 overspeed 怠速 idling 转速波动率 speed fluctuation rate 工况 working condition(operating mode) 额定工况 declared working condition 变工

23、况 variable working condition 稳定工况 steady working condition 空载 no-load 全负荷 full load 超负荷 overload 部分负荷 part load 充量（进气） charge 旋转方向 direction of rotation 顺时针 clockwise 逆时针 counter-clockwise 左转 left-hand rotation 右转 right-hand rotation 外径 major diameter 中径 pitch diameter 内径 minor diameter 径向间隙 radial

24、clearance 发动机性能 engine performance 加载性能 loading performance 起动性能 starting performance 加速性能 acceleration performance 动力性能 power performance 排放性能 emission performance 空转特性 no load characteristics 负荷特性 part throttle characteristics 调速特性 governor control characteristics 万有特性 mapping characteristics 稳定调速

25、率 steady state speed governing rate 气缸体和气缸盖 cylinder block and head 气缸体 cylinder block 整体铸造 cast inblock (cast enblock) 发动机罩 engine bonnet 气缸体加强筋 engine block stiffening rib 气缸 cylinder （转子机）缸体 stator 缸径 cylinder bore 气缸体机架 cylinder block frame 气缸盖 cylinder head 配气机构箱 valve mechanism casing 气缸体隔片 cy

26、linder spacer 气缸盖密封环 cylinder head ring gasket 气缸盖垫片 cylinder head gasket 气缸套 cylinder liner(cylinder sleeve) 干式缸套 dry cylinder liner 湿式缸套 wet cylinder liner 气缸水套 water jacket 膨胀塞 expansion plug 防冻塞 freeze plug 气缸壁 cylinder wall 环脊 ring ridge 排气口 exhaust port 中间隔板 intermediate bottum 导板 guideway 创成半

27、径（转子机） generating radius 缸体宽度（转子机） operating width 机柱 column 燃烧室 combustion chamber 主燃烧室 main combustion chamber 副燃烧室 subsidiary combustion chamber 预燃室 prechamber 涡流燃烧室 swirl combustion chamber 分开式燃烧室 divided combustion chamber 涡流式燃烧室 turbulence combustion chamber 半球形燃烧室 hemispherical combustion cha

28、mber 浴盆形燃烧室 bathtub section combustion chamber L形燃烧室 L-combustion chamber 楔形燃烧室 wedge-section combustion chamber 开式燃烧室 open combustion chamber 封闭喷射室 closed spray chamber 活塞顶内燃烧室 piston chamber 爆发室 explosion chamber 燃烧室容积比 volume ratio of combustion cahmber 燃烧室口径比 surface-volume ratio of combustion c

29、hamber 通道面积比 area ratio of combustion chamber passage 曲轴箱通气口 crankcase breather 凸轮轴轴承座 camshaft bearing bush seat 定时齿轮室罩 camshaft drive(gear)cover 曲轴箱检查孔盖 crankcase door 曲轴箱防爆门 crankcase explosion proof door 主轴承盖 main bearing cap 气缸盖罩 valve mechanism cover 飞轮壳 flywheel cover 扫气储器 scavenging air rece

30、iver 活塞 piston 裙部开槽活塞 split skirt piston U形槽活塞 U-slot piston 滚花修复活塞 knurled piston 圆顶活塞 dome head piston 平顶活塞 flat head piston 凸顶活塞 crown head piston(convex head piston) 凹顶活塞 concave head piston 阶梯顶活塞 step-head piston 筒形活塞 trunk piston 椭圆形活塞 oval piston 抗热变形活塞 autothermic piston 不变间隙活塞 constant clea

31、rance piston 镶因瓦钢片活塞 invar strut piston 直接冷却式活塞 direct-cooled piston 间接冷却式活塞 indirect cooled piston 滑裙活塞 slipper piston 活塞速度 piston speed 活塞顶部 piston head 活塞裙部 piston skirt 整体活塞裙 solid skirt 活塞裙扩大衬簧 piston skirt expander 滑履式活塞裙 slipper skirt 隔热槽 heat dam 活塞标记 piston mark 活塞销 piston pin 活塞销孔 piston p

32、in boss 活塞销衬套 piston pin bushing 全浮式活塞销 full-floating piston pin 半浮式活塞销 semifloating piston pin 固定螺钉式活塞销 set screw piston pin 活塞环 piston ring 组合式活塞环 compound piston ring 同心活塞环 concentric piston ring 偏心活塞环 eccentric piston ring 自由环 free ring 闭合环 closed ring 梯形环 keystone ring 半梯形环 half keystone ring 矩

33、形环 rectangular ring 油环 oil control ring 开槽油环 slotted oil control ring 螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander 双坡口油环 double bevelled oil control ring 内上坡口 internal bevel top 内下坡口 internal bevel bottom 边缘坡口油环 bevelled-ege oil control ring 刮油环 scrapper ring 钩形环 napier ring 镀

34、铬活塞环 chrome plated piston ring 活塞衬环 piston ring expander 活塞环槽 piston ring groove 活塞环区 ring zone 活塞环岸 piston ring land 活塞环内表面 back of ring 曲柄连杆机构 connecting rod 中心曲柄连杆机构 central-located connecting rod 偏心曲柄连杆机构 offset connecting rod 铰接曲柄边杆机构 hinged connecting rod 连杆 connecting rod 连杆小头 connecting rod

35、small end 连杆大头 connnecting rod big end 连杆杆身 connecting rod shank 副连杆 slave connecting rod 叉形连杆 fork-and-blade connecting rod 主连杆 main connecting rod 方形连杆 boxed rod 绞链式连杆 hinged type connecting rod 活节式连杆 articulated connecting rod 连杆盖 connecting rod cap 连杆轴承 connecting rod bearing 曲轴 crankshaft 整体式曲轴

36、 one-piece crankshaft 组合式曲轴 assembled crankshaft 右侧曲轴 right-hand crankshaft 左侧曲轴 left-hand crankshaft 改变行程的曲轴 stroked crankshaft 曲轴前端 crankshaft front end 曲轴主轴颈 crankshaft main journal 轴颈重叠度 shaft journal overlap 圆角 fillet 主轴承 main bearing 曲轴止推轴承 crankshaft thrust bearing 薄臂轴瓦 thin wall bearing shel

37、l 曲轴油道 crankshaft oil passage 曲柄 crank 曲柄臂 crank arm 曲柄销 crank pin 轴套 bush 曲柄转角 crank angle 曲柄半径 crank radius 抛油圈 oil slander 角度轮 degree wheel 动平衡机 dynamic balancer 平衡重 balancer weight 扭振减振器 torshional vibration damper 扭振平衡器 torsion balancer 谐振平衡器 harmonic balancer 振动平衡器 vibration balancer 曲轴链轮 cran

38、kshaft sprocket 转子轴颈 rotor journal 偏心轴 eccentric shaft 曲轴箱 crankcase 闭式曲轴箱通风装置 closed-crankcase ventilating system 飞轮 flywheel 飞轮齿圈 flywheel ring gear 飞轮芯棒 cantilever 飞轮芯轴 flywheel spindle 飞轮的惯量矩 flywheel moment of inertia 飞轮标记 flywheel mark 当量系统 equivalent system 当量轴长 equivalent shaft length 一级往复惯性

39、力 reciprocating inertia force,1st order 二级往复贯性力 reciprocating inertia force, 2nd order 离心惯性力 centrifugal inertia force 配气机构 valve gear 凸轮轴 camshaft 凸轮 cam 整体式凸轮轴 one-piece camshaft 组合式凸轮轴 assembled camshaft 凸轮轴驱动机构 camshaft drive 赛车用凸轮轴 race camshaft 凸轮轴轴颈 camshaft bearing journal 凸轮轴轴承 camshaft bea

40、ring 凸轮轴偏心轮 camshaft eccentric 凸轮轴链轮 camshaft sprocket 凸轮轴正时齿轮 camshaft timing gear 凸轮轴齿轮 camshaft gear wheel 进口凸轮 inlet cam 排气凸轮 exhaust cam 快升凸轮 quick lift cam 快升缓降凸轮 quick lift gradual clsing cam 凸轮轮廓 cam contour 凸轮包角 cam angle 凸轮升程 cam-lobe lift 凸轮尖 cam nose 凸轮从动件 cam follower 齿轮传动机构 gear drive

41、正时齿轮 timing gear 链传动机构 chain drive 链轮 sprocket wheel 链轮盘 chain sprocket 正时链条 timing chain 带齿皮带 toothed timing belt 链条张紧轮 chain tension gear 半速齿轮 half speed gear 正时齿轮刻印记号 timing gear punch mark 气门 valve 进气过程 intake process 换气过程 gas exchange process 扫气过程 scavenging process 给气比 delivery ratio 分层充气 stra

42、tified charge 充量系数 volumetric efficiency 涡流比 swirl rate 进气涡流 intake swirl 螺旋进气道进气 helical duct intake 导流屏式气门进气 masked valve intake 切向进气道进气 tangential duct intake 进气紊流 intake trubulence 进气提前角 intake advance angle 进气持续角 intake duration angle 进气迟后角 intake lag angle 进面值 time-area value 气门升程 valve lift 气

43、门正时 valve timing 扫气口面积 scavenging port area 菌形气门 mashroom valve, poppet valve 钠冷却气门 sodium filled valve(natrium cooled valve) 双气门 dual valve 进气门 intake valve (suction valve,inlet valve) 排气门 exhaust valve 顶置气门 overhead valve 侧置气门 side valve 倾斜气门 inclined overhead valve 直立气门 vertical overhead valve 套筒式滑阀 sleeve valve 气门机构 valve gear 直接式气门驱动机构 direct valve gear 间接式气门驱动机构 indirect valve gear 气门杆 valve stem 加大气门杆 oversize valve stem 气门头 valve head 气门工作面 valve face 气门边限 valve margin 气门弹簧座 valve-spring retainer 气门锁片 valve key 气门间隙调节螺钉 valve lash adjusting screw