《DELL服务器配置教程raid.docx》由会员分享，可在线阅读，更多相关《DELL服务器配置教程raid.docx（15页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、目录一，系统设置： 二，配置 Raid三，主机系统安装：12 开机按F11 ,进入系统安装选项：12一，系统设置:1.查看bios设置：开机按F2 ,进入bios2.进入F2.如图：进入System BIOS &项 System SetupSystem Setup Mas MenuHH3,找到 System BIOS 选项里的 SATA Settings 选项，把 Embedded SATA 设置成 AHCI Mode.如图:4.按esc返回上一级菜单,并找到Boot Settings选项，Boot Mode选择BIOS ,如图:退出并保存，选yes如图:System Setip询 I Abo
2、ut I ExitSystem BIOS System BIOS SettngsSystem InfcrmationMemory SettngsProcessor SettngsSATA S湘购$Bo况S机UgsNHwockSWngg|0【列8 膊 d Doyles涵同 CanmunK&sSystem Pron-SenngsSystem SecunlyPowE 妍 R73OServte Teg-选ok ,如图:System SetupWarningI Sa vt)g ChangesS机togs have chenged. Do you wrt to save the chants?(Note:
3、 One or nwe of the changes reqores a system rest to takeSavog chaiges now wlnotcause an immediate reset. Instead, the reset occur after exiting thrs utlity.)NoAniihHelp I About I ExitSystem BIOSSystem BOS SettingsSystem InformationMemory SeinngsProc 收 x SwngsSA SEUngsBoot SettingsMeMBk SeHngs暄列8冷。De
4、vicesSenal CxnmjrK8isSystem Prohl。SoiEgsSystem SecurityPowerEcB R730 SrvKeTdg：5VW$4S2DefaultFinish7.点击Finish ,如图:System SetupHevi AUxn I ExitSystem SetupSystem Setup Main MenuSysiem BQSQRAC SeigDevice SettingsSetect to confute system BIOS settings.PowEdge R73OService Taa:8,选yes ,如图:System SetipHoE A
5、bout I ExitSystem SetupSystem Setip Main MenuSystBOSDevice SettingsPowerEdge R73O Service T ag9,完成后进入raid配置界面,bios设置完成。配置Raid1.重启，直到屏幕上出现Ctrl + R的提示，快速按下Ctrl键+字母R键，如图FZ = System SetupF19 = Lifecycle Controller (Config iDRAC, Update FW, Install OS) Fll = Boot ManagerF1Z = PXE BootBroadcom MetXtreMe E
6、thernet Boot Agent Copyright (C) 2000-2017 Broadcom Corporation Al 1 rights reserved.Press Ctr1-S to enter Conf iguration MenuInitializing Serial ATA devices.Port J： PLDS DUD*/-RU DS-8ABSHPowerEdge Expandable RAID Controller BIOS Copyright(c) Z016 Avago TechnologiesPress to Run Conf igurat ion Util
7、ity2.进入Raid配置界面:3.光标选到阵列长(H330/H730/H730P)，如图:4.按下F2,看仔哪些选项,如果如下图,则选ForeignConfig Clear ,然后问车：如图:选中两块硬盘，然后点击如下图PERC H330BIOSo?eiCANCEL原创聲档Ready ReadyDisk Gioupv: 6 Ulrtun ! D!:kN : Physical DisksF1Z选到阵列长 H330/H730/H730P; F2 g 如云图f选 Create NewPERC H339BIOS Conf igurat ion18-9701CtrI Mgmt Properties直到
8、硬盘是Ready状态（准备状态），如下图PERC H336fBus 8x03. Dgv Ox0e) ion Present !1 Disks090 TBese tbCreate MewForeign Conf igPERC H33。ini (Bus 8x83. Dev 0x60) No Conf igurat ion Present !-Unconf igured Physica1 DisksI 00:01:00： Ready： 1.690 TB1 OO：ei：et： Ready： 1.090 TBManage Preserved CacheSecur ity Key ManageConver
9、t|F1 Help FZ-Operat iF5 RcCtCtpm9.选择raid级别，本次选RAID-1.如图:5.i8-e?ei10,选中磁盘并下翻到Advanced ,然后按Enter进入：如图:12.选ok ,如图:PERC 11330 Mini BIOS Coe?ei14.选ok：15.选ok :18.选okPERC H33O Mini BIOS Conf iguration Utility 5.18 070119, 提示按Control +Alt+Delete键重启，到此raid配置完成:Press ControlItDelete to reboot三，主机系统安装: 开机按F11
10、,进入系统安装选项:FZ = System SetupF10 = Lifecycle Controller (Config iDRAC. Update FW, Install OS) Fll = Boot ManagerFIZ = PXE BootBroadcom NctXtrci*e Ethernet Boot Agent Copyright (C) 2000-2017 Broadcom Corporation Al 1 rights reserved.Press Ctr1-S to enter Conf iguration MenuF2 二 System SetupF10 = recycl
11、e Controlr (Comg ORAC. Ltxlate FW.Instal OS) Enicg Scot Mg的F12 = PXE Boot1.如下图:PowerEdge RT30 BIOS Version Z&O2.选到 One-shot BIOS Boot Menu 选项,并进入:3.选择从DVD启动，如下图:Boot Marker*p I About I ExitBoot ManagerBoot MenuS4ect Legacy Boot Option Embedded SATA Pert Optical Crrve 上 PLDS DVDZ-RW DS.8ABSH |Hard UW8 加 RAD QW01W 1： PERC Wu$ 03 妍 00)int沖aled NIC 1 Po” 1 Parbhon 1:8PCM 淄 SW 0100 y20.6.50vmual Floppy Virtual OptKei Drive Oof。Path: PaRooKOxOyPcKOx F.Ox2|/Sata(OK5.0xO.OxO)AnahPowEdge R73O ServKe Tag: