《模具毕业设计外文翻译(英文+译文).docx》由会员分享，可在线阅读，更多相关《模具毕业设计外文翻译(英文+译文).docx（9页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、模具毕业设计外文翻译(英文+译文) Injection Molding The basic concept of injection molding revolves around the ability of a thermoplastic material to be softened by heat and to harden when cooled .In most operations ,granular material (the plastic resin) is fed into one end of the cylinder (usually through a feedin
2、g device known as a hopper ),heated, and softened(plasticized or plasticized),forced out the other end of the cylinder, while it is still in the form of a melt, through a nozzle into a relatively cool mold held closed under pressure.Here,the melt cools and hardens until fully set-up. The mold is the
3、n opened, the piece ejected, and the sequence repeated. Thus, the significant elements of an injection molding machine become: 1) the way in which the melt is plasticized (softened) and forced into the mold (called the injection unit); 2) the system for opening the mold and closing it under pressure
4、 (called the clamping unit);3) the type of mold used;4) the machine controls. The part of an injection-molding machine, which converts a plastic material from a sold phase to homogeneous seni-liguid phase by raising its temperature .This unit maintains the material at a present temperature and force
5、 it through the injection unit nozzle into a mold .The plunger is a combination of the injection and plasticizing device in which a heating chamber is mounted between the plunger and mold. This chamber heats the plastic material by conduction .The plunger, on each stroke; pushes unbelted plastic mat
6、erial into the chamber, which in turn forces plastic melt at the front of the chamber out through the nozzle The part of an injection molding machine in which the mold is mounted, and which provides the motion and force to open and close the mold and to hold the mold close with force during injectio
7、n .This unit can also provide other features necessary for the effective functioning of the molding operation .Moving plate is the member of the clamping unit, which is moved toward a stationary member. the moving section of the mold is bolted to this moving plate .This member usually includes the e
8、jector holes and mold mounting pattern of blot holes or “T” slots .Stationary plate is the fixed member of the clamping unit on which the stationary section of the mold is bolted .This member usually includes a mold-mounting pattern of boles or “T” slots. Tie rods are member of the clamping force ac
9、tuating mechanism that serve as the tension member of the clamp when it is holding the mold closed. They also serve as a gutted member for the movable plate .Ejector is a provision in the clamping unit that actuates a mechanism within the mold to eject the molded part(s) from the mold .The ejection
10、actuating force may be applied hydraulically or pneumatically by a cylinder(s) attached to the moving plate, or mechanically by the opening stroke of the moving plate. Methods of melting and injecting the plastic differ from one machine to another and are constantly being implored .conventional mach
11、ines use a cylinder and piston to do both jobs .This method simplifies machine construction but makes control of injection temperatures and pressures an inherently difficult problem .Other machines use a plasticizing extruder to melt the plastic and piston to inject it while some hare been designed
12、to use a screw for both jobs :Nowadays, sixty percent of the machines use a reciprocating screw,35% a plunger (concentrated in the smaller machine size),and 5%a screw pot. Many of the problems connected with in ejection molding arise because the densities of polymers change so markedly with temperat
13、ure and pressure. thigh temperatures, the density of a polymer is considerably cower than at room temperature, provided the pressure is the same.Therefore,if molds were filled at atmospheric pressure, “shrinkage” would make the molding deviate form the shape of the mold. To compensate for this poor
14、effect, molds are filled at high pressure. The pressure compresses the polymer and allows more materials to flow into the mold, shrinkage is reduced and better quality moldings are produced.Cludes a mold-mounting pattern of bolt holes or “T” slots. Tie rods are members of the clamping force actuatin
15、g mechanism that serve as the tension members of clamp when it is holding the mold closed. Ejector is a provision in the calming unit that actuates a mechanism within the mold to eject the molded part(s) form the mold. The ejection actuating force may be applied hydraulically or pneumatically by a c
16、ylinder(s) attached to the moving plate, or mechanically by the opening stroke of the moving plate. The function of a mold is twofold: imparting the desired shape to the plasticized polymer and cooling the injection molded part. It is basically made up of two sets of components: the cavities and cor
17、es and the base in which the cavities and cores are mounted. The mold ,which contains one or more cavities, consists of two basic parts :(1) a stationary molds half one the side where the plastic is injected,(2)Moving half on the closing or ejector side of the machine. The separation between the two
18、 mold halves is called the parting line. In some cases the cavity is partly in the stationary and partly in the moving section. The size and weight of the molded parts limit the number of cavities in the mold and also determine the machinery capacity required. The mold components and their functions
19、 are as following: (1)Mold Base-Hold cavity (cavities) in fixed, correct position relative to machine nozzle. (2)Guide Pins-Maintain Proper alignment of entry into mold interior. (3)Spree Bushing (spree)-Provide means of entry into mold interior. (4)Runners-Conroy molten plastic from spree to caviti
20、es. (5)Gates-Control flow into cavities. (6)Cavity (female) and Force (male)-Control the size, shape and surface of mold article. (7)Water Channels-Control the temperature of mold surfaces to chill plastic to rigid state. (8)Side (actuated by came, gears or hydraulic cylinders)-Form side holes, slot
21、s, undercuts and threaded sections. (9)Vent-Allow the escape of trapped air and gas. (10)Ejector Mechanism (pins, blades, stripper plate)-Eject rigid molded article form cavity or force. (11)Ejector Return Pins-Return ejector pins to retracted position as mold closes for next cycle. The distance bet
22、ween the outer cavities and the primary spree must not be so long that the molten plastic loses too much heat in the runner to fill the outer cavities properly. The cavities should be so arranged around the primary spree that each receives its full and equal share of the total pressure available, th
23、rough its own runner system (or the so-called balanced runner system).The requires the shortest possible distance between cavities and primary sprue, equal runner and gate dimension, and uniform culling. 注射成型 注射成型的基本概念是使热塑性材料在受热时熔融，冷却时硬化，在大部分加工中，粒状材料（即塑料树脂）从料筒的一端（通常通过一个叫做“料斗”的进料装置）送进，受热并熔融（即塑化或增塑），然
24、后当材料还是溶体时，通过一个喷嘴从料筒的另一端挤到一个相对较冷的压和封闭的模子里。溶里在模腔里冷却，硬化，直至完全固化。然后将模子打开，推出工件，并重复以上工序。 因此，注塑成型机的重要组成部分是：1）将溶体塑化并挤进进模腔（称做“注塑单元”）；2）开模和家压合模9称为“合模系统”）；3）使用上午模具类行；4）机器控制。 注射装置通过家热将固态塑料转化成均匀的半液态塑体。它保持塑料当前温度并加压使之通过喷嘴进入模具。柱塞集塑化和注射为一体。在柱塞与模具之间没有加热室，几热室通过热传导加热塑料。每次行程，柱塞将待熔化塑料推入加热室，依次将熔化的塑料挤到加热室前端并通过喷嘴注射出去（注射到模具中去
25、） 合模装置是注射成型机的一个部分，该装置上安装有模具。合模装置提供运动和动力以开模几合模，并且在注射过程中提供压力保持模具紧闭同时，该装置还提供成型工艺有效运动所必需的其它特性。动模板是合模装置的一部分，在合模时向定模板移动。型腔的运动部分用螺栓固定在动模板上，动模板通常动模板通常含顶出杆，螺栓空或T 型槽的安装模具的型板。拉杆是合模力驱动机构中的一个构件，当夹具保持动模闭合时，拉杆起夹具的拉力构件的作用。顶出器是合模装置的一个部件，它驱动模具中的执行机构从模具中顶出成型制品。顶出力可由液压或气动装置通过装在动模板上的油（气）缸来施加，或者通过动模板开模行程来施加。 塑料熔融与塑料注射的方式随机器的不同而不同,并不断得以改善。常规的机器采用一个料筒和一个活塞来进行熔融和注射。虽然这种方式简化了机器的结构，但却使注射的温度和压力控制成了一个固有的难题。有的机器用一个塑化挤压器来熔化塑料，用一个活塞进行注射。另外，还有一些已设计出来的机器采用一个螺杆来完成熔融和注射。目前，百分之六十的机器采用往复式螺杆，百分之三十五的机器采用柱塞；百分之六十的机器采用螺罐。 聚合物的密度在不同的温度和压力下变化很大，并由此产生了注射成型的许多问题。在压力不变的情况下，在高温下的聚合物的密度