《2022年模具专业术语英文 .pdf》由会员分享，可在线阅读，更多相关《2022年模具专业术语英文 .pdf（4页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、注塑、模具专业英语Surface Appearance外观Glossiness/gloss finish光洁度、粗糙度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface玻纤外露、浮纤Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹、料花Flow mark流纹Brittle/brittleness脆、脆性Bubbles/trapped gas
2、气泡 /困气Void 孔、气泡Burn marks烧伤FR failed 阻燃不合格Flame rating V-2阻燃等级 V-2Poor dispersion分散不好FR/PTFE agglomerates etc 阻燃剂 /PTFE 结块Pellet porous颗粒料孔隙、Low impact/tensile strength etc低冲击强度 /拉伸强度等High flow/filler content etc高流动性 /过度填充Longs/fines/doubles长粒 /碎屑 /连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles 纤维
3、结团Product was rejected due to 产品不能接受因为High moisture level 高水分、高湿度Warpage/warped翘曲 /变形Shrinkage/shrink收缩 /收缩率Sink marks凹陷、缩水Short shot/short molding打不满、欠注Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing 飞边、披锋、溢边Discoloration变色Off color 颜色差异Flow rate 流动速率Viscous/viscosity粘性的、粘的 /黏度High flow 高
4、流动Low flow 低流动Sticky粘的，粘性的精选学习资料 - - - - - - - - - 名师归纳总结 - - - - - - -第 1 页，共 4 页Sticking core粘后模，粘模芯Sticking sprue 粘水口Sticking cavity 粘前模Mold release （ agent） 脱模 (剂 )Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱 /长玻纤Glass beads玻璃微珠Milled fibe
5、r碾磨纤Molybdenum disulfide/moly/MoS2二硫化钼Colorant 着色剂Pigment颜料Dye 染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra 添加多一点Reduced content减少含量Dropped/reduced by x 减少含量Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准
6、Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by 预计在完成Expected order is xMT预计定单量吨Estimated annual/monthly consumption预计年 / 月用量模具方面：Ejection system顶出系统、脱模系统pin顶针、推杆spring弹簧Gate type浇口类型Sprue主流道runner分流道cavit
7、y模腔Sprue gate直浇口Pin point gate 点浇口Tab gate 护耳浇口Fan gate 扇形浇口Tunnel or submarine gate潜伏式浇口精选学习资料 - - - - - - - - - 名师归纳总结 - - - - - - -第 2 页，共 4 页Jump gate跳跃式浇口Diaphragm gate片状浇口Ring gate 环形浇口The cavity of the mould模腔Heated cylinder加热料筒Surface finish 表面光洁度Sink mark缩水Air trap困气Gas trapped气体困着，困气void 空
8、隙，孔galling烧焦Weld line 熔接痕，熔合线Drag mark划伤、脱模痕Scratch mark模具刮花Deformed/ warp变形Ejector not returned顶针不回位slide 滑块、行位streak波纹、条纹、色痕delamination分层Jetting mark喷射痕Gate mark浇口痕rib筋、加强筋、骨位boss凸台、凸起、凸痕Melt flow length熔体流线长度Ejector plate顶针板Stop pin限位销Push rod 推杆、顶针Push back pin 复位杆Ejector guide pin顶针导柱Cold-slug
9、-well 冷料井、冷料穴plate模板Ejected mark顶痕，顶白nozzle喷嘴Surface defect 表面缺陷Air vent排气口Filling uneven 走胶不平衡、进胶不平衡pressure:压力speed:速度control: 控制protection pressure: 保压mold: 模set:设定option: 选择injection: 射胶精选学习资料 - - - - - - - - - 名师归纳总结 - - - - - - -第 3 页，共 4 页pressure reducing valve :减压阀relief valve: 泄压阀max:最大max:最大system:系统proportional: 比例pressure transducer: 压力传感器sampling 试模pressure sensor 压力感应器AMP 伺服放大器trial runrunninggatedosage 溶胶clamp open 开模精选学习资料 - - - - - - - - - 名师归纳总结 - - - - - - -第 4 页，共 4 页