环氧面漆用户手册.doc

《环氧面漆用户手册.doc》由会员分享，可在线阅读，更多相关《环氧面漆用户手册.doc（11页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。

1、【精品文档】如有侵权，请联系网站删除，仅供学习与交流环氧面漆用户手册.精品文档.C1842环氧云铁防锈漆(primer)Q/GHTD 81组 成 以环氧树脂、聚酰胺树脂固化剂、灰色云母氧化铁、防锈颜料、助剂和溶剂等组成的双组份环氧防锈漆。主要特性 。在喷砂钢铁上具有优异的附着力 。在适当处理的镀锌钢材及铝合金上具有优良的附着力 。在富锌底漆和钢铁的喷锌层上具有优良的附着力和封闭性能 。在工业和化学大气环境下有良好的耐候性和耐蚀性 。表面有一定的粗糙度，与环氧、氯化橡胶、聚氨酯面漆具有很好的配套性能，也能与醇酸、酚醛等传统型漆配套，与后道漆膜具有良好的层间附着力 。具有良好的耐磨性 。具有良好的

2、防锈性能和耐久性 。获中国船级社的型式认可用 涂 可作为环氧富锌底漆、无机锌底漆等高性能防锈漆的中间涂层，以增强整个涂层的层间附着力和保护性能；可以用于镀锌钢材、铝合金表面作底漆之用；也可直接涂装在喷砂处理的钢材表面作防锈底漆之用。广泛用于船舶和陆上钢结构的重防腐蚀体系。外 观 灰色、无光施工参数 体积固体份 623%（按GB/T9272 eqv ISO3233:1998规定测定）（混合后） 配比 甲组份：乙组份=7:1(重量比) 干膜厚度 80-120 m 湿膜厚度 129-194m 理论用量 215-324/ 闪点 甲组份（基料） 27 乙组份（固化剂）27 干燥时间（25） 表干2h 实

3、干24h 完全固化 7d 熟化时间 （混合后20） 30min适用期 （混合后20） 8h(气温大于30以上时，甲乙组份混合后适用期随着气温的升高而缩短)复涂间隔时间温度52030最短48h24h16h最长无限制备注：关于“无限制”的含义请见补充说明建议涂装道数 无气喷涂一道，刷涂或滚涂2-3道，干膜厚度80-120m前道配套底漆 H06-4环氧富锌防锈漆、E06-1无机硅酸锌防锈漆、H53-42环氧封闭涂料、H53-32环氧磷酸锌防锈漆等环氧防锈漆。或直接涂装在除锈质量达到Ss2.5级的钢铁表面上，或经打毛后的铝金表面上。后道配套用漆 聚氨酯面漆、氯化橡胶面漆、丙烯酸面漆、环氧面漆、环氧沥青

4、防锈漆、醇酸面漆等表面处理 。涂有富锌底漆的钢铁：除尽所有油污、杂物和锌盐 。镀锌钢材：以风动或电动弹性砂轮片打磨除尽所有的油污、杂物和锌盐；如用于水下部位则必须采用轻扫喷砂进行表面处理 。钢铁：喷砂处理至Sa2.5级 。涂有车间底漆钢材：漆膜损伤处、锈蚀处及含锌底漆上的白绣处进行二次除锈，除白绣并打磨至St3级 。铝合金：船底部位采用轻扫喷砂打毛，水线或陆上部位用砂纸打毛 。与可以配套的旧漆膜：除尽所有的油污杂物后将旧漆膜打毛施工条件 。底材温度须高于露点以上3 。在室外施工底材温度低于5时，请选用冬用型842环氧云铁防锈漆 。相对湿度不大于85%涂装方法无气喷涂 稀释剂 103稀释剂 稀释

5、量 0-5%（以油漆重量计算） 喷嘴口径 0.4-0.5mm 喷出压力 20-25MPa（约200-250kg/c）空气喷涂 不推荐用于大面积施工，仅适用于小面积修补或小型被涂件 稀释剂 103稀释剂 稀释量 0-10%（以油漆重量计） 喷嘴口径 2.0-3.0mm 空气压力 0.3-0.4MPa（约3-4 kg/c）滚涂/刷涂 稀释剂 103稀释剂 稀释量 0-3%（以油漆重量计）清洗剂 103稀释剂安全措施 参见上海开林造漆厂产品安全技术说明书（简称MSDS）包装 甲组份 20L 桶装 21kg 乙组份 4L 桶装 3kg保质期 12个月备注 为正确使用本厂的产品，请仔细阅读本说明书中的使

6、用指南.补充说明 。842环氧云铁防锈漆的干燥和固化时间随温度的升高而缩短。不同温度时固化时间参考如下：温度510152030表干4h3h2.5h2h1h实干60h48h36h24h16h完全固化-15d10d7d5d .气温在5-10之间能进行842环氧云铁防锈漆的施工，但是固化速度很慢 。气温低于5时，因环氧树脂与固化剂反应停止，不宜进行施工。在这种情况下，可在温度高于5以上的涂装车间进行施工。或选用842（冬用型）环氧云铁防锈漆 。在842环氧云铁防锈漆的施工和固化期间需要充分的通风换气 。842环氧云铁防锈漆在漆膜表面没有粉化或被其他物质污染时，一般没有最长涂装间隔的限制。但是在漆膜完

7、全固化前涂装下道油漆，则会获得最好的层间附着力。如果842环氧云铁防锈漆的漆膜在大气环境中暴露较长时间之后才涂装下道油漆，则应特别注意漆膜表面的清洁并用打磨方法去除粉化层，以获得良好的附着力 。在涂装中如842的漆膜厚度过厚时，或涂装时相对湿度大于85%时，漆膜将会呈现光滑表面。在进行下道面漆的施工前，须用砂纸进行打毛，以增加漆膜层间的附着力声明 以上本产品的资料及数据是根据我们的试验和实际使用中的经验而积累的，可作为施工指南。对于在我们不了解的情况下进行的施工，我们只保证油漆本身的质量，其它方面的问题恕不负责。对本说明书，我们将根据产品的不断改进有权进行修改。842 epoxy micace

8、ous iron rust (primer)Q / GHTD 81GENERIC TYPEComposed of an epoxy resin, polyamide resin curing agent, gray micaceous iron oxide, rust pigments, additives and solvents consisting of two component epoxy anti-rust paint .GENERAL PROPERTIES Blasting with excellent adhesion on steel. In the proper treat

9、ment on galvanized steel and aluminum alloy with excellent adhesion. In zinc-rich primer and spray zinc layer on the steel has excellent adhesion and sealing characteristics. In the industrial and chemical atmospheric environment with good weather resistance and corrosion resistance. Have a certain

10、surface roughness, and epoxy, chlorinated rubber, polyurethane topcoat with good supporting performance , but also with alkyd , phenolic and other traditional paint facilities, and after- film has good adhesion between the layers. Has good wear resistance characteristic. Has good rust resistance and

11、 durability. Type approved by China Classification SocietyTYPICAL USESCan be used as epoxy coated zinc-rich primer, inorganic zinc primer in the middle of high performance anticorrosive coating to enhance the overall coating adhesion between the layers and protective properties; can be used in galva

12、nized steel, aluminum alloy surface primer for purposes; also be directly coated on a blasted steel surface for rust primer purposes. Widely used in marine and land-based heavy steel structures anti- corrosion system.Appearance gray, mattConstruction parameters Solids 62 3% (according to GB/T9272 eq

13、v ISO3233: 1998 requirements determination) (mixed)Ratio Part A: B = 7:1 (weight ratio) Dry film thickness 80-120 m Wet film thickness 129-194m Theoretical amount 215-324 / Flash Point Part A (base) 27 Part B (curing agent) 27 Drying time (25 ) Surface dry 2h Drying 24h Fully cured 7d Curing time (a

14、fter mixing 20 ) 30minPot life (after mixing 20 ) 8h(Temperatures greater than 30 or more, and B after mixing pot life at higher temperatures and shorter)Recoat interval温度Temperature52030最短Least48h24h16h最长LongestNo limitationRemark: about the meaning of unlimited please see addedRecommended layers 1

15、 layer of airless spray2-3 layers by brush or roller, dry thickness film 80-120umSupporting primer Before primers H06-4 epoxy zinc-rich anticorrosive paint, inorganic zinc silicate anticorrosive paint, H53 E06-1-42 epoxy sealing coatings, H53-32 zinc phosphate epoxy antirust paints such as epoxy ant

16、irust paint. Or direct coating in derusting quality Ss2.5 level on the surface of the steel, or aluminum gold surface after dozen hairSupporting next coating After the coats of polyurethane paint, chlorinated rubber paint, acrylic paint, epoxy paint, epoxy asphalt anticorrosive paint, alkyd paint, e

17、tcPreparation The steel has been spray Rich-zinc: in addition to all the oil pollution, sundry and zinc salt. Galvanized steel: with pneumatic or electric elastic grinding wheel grinding in addition to the best of all the pollution, clutter and zinc salt; If it is used in the underwater part must ad

18、opt swept gently sandblasting surface treatment. Steel: sandblasting to Sa2.5 . Steel coated with shop primer, paint film damage, corrosion, and the white embroidered on the zinc primer for secondary cleaning, in addition to white embroidery and polished to St3 . Aluminum alloy: bottom parts adopt s

19、wept gently gush arenaceous dozen hair, water or land beat hair with sandpaper. Coordinate the old film: in addition to all the oil from clutter will play MAO old paint filmConstruction conditions. The substrate temperature must be higher than 3 above the dew point. Outside construction substrate te

20、mperature below 5 , please choose winter type 842 epoxy micaceous iron oxide antirust paint. Relative humidity is not greater than 85%The coating methodAirless spray is thinner, 103 ThinnerDilution 0-5% (weight) Nozzle diameter 0.4-0.5 mmOutput pressure 20 to 25 mpa (about 200-250 kg/c )Air sprayAir

21、 spray is not recommended for large area construction, applies only to repair small goodsThinner, 103 ThinnerDilution 0-10% (weight)Nozzle diameter 2.0-3.0 mmAir pressure 0.3-0.4 MPa (about 3-4 kg/c )Roller coating/brush thinner 103 ThinnerDilution 0-3% (weight)Cleaner 10 ThinnerSafety measures Safe

22、ty measures see Shanghai Kailin paint factory Product Safety Data Sheet (MSDS) whichPackaging component Component A 20 liters 21 kgComponent B 4 liters 3 kgPot life 12 monthsNote for the correct use of our factory product, please read the use guide in this manual carefully.Add 842 epoxy micaceous ir

23、on oxide antirust paint drying and curing time shortened with the rise of temperature. Different temperature curing time reference is as follows:温度Temperature510152030表干Touch4h3h2.5h2h1h实干Handle60h48h36h24h16h完全固化Fully cured-15d10d7d5dThe temperature at 5-10 can carry 842 epoxy micaceous iron rust c

24、onstruction, but the cure rate is very slow. When the temperature below 5 , the epoxy resin and curing agent reaction would stop and need to stop product. In this case, we can product in the workshop whose temperature is higher than 5 , Or use 842 (winter type) epoxy micaceous iron rust. 842 epoxy m

25、icaceous iron rust in the construction and curing the need for adequate ventilation during. 842 epoxy micaceous iron rust on the paint surface is not chalking or other substances contaminated, there is normally no overcoating interval limits. But in the film coating is fully cured before the next ro

26、ad paint, you will get the best adhesion between the layers . 842 epoxy micaceous iron rust if the film is exposed to the atmosphere after a long time under the road paint coating should pay particular attention to the film surface clean and polished to remove a layer of powder to get a good attachm

27、ent focus. In the painting, such as 842 in the film thickness is too thick, or paint when the relative humidity is greater than 85%, the film will show a smooth surface. During pre-construction under the topcoat shall be roughened with sandpaper to increase the adhesion between the film layerDeclare

28、 that the product information and data are based on our testing and actual use of the experience accumulated, as a construction guide. For we do not know the circumstances of the construction, we can only guarantee the quality of the paint itself, other aspects will not be responsible. Of this manua

29、l, we will continue to improve the product to be made.各色环氧面漆(finish coating)Q/GHTD 85组 成 由环氧树脂、聚酰胺固化剂，钛白粉、着色颜料、体质颜料、助剂和溶剂等组成的双组份环氧漆。主要特性 . 固体含量高，可制成厚膜型环氧面漆 . 漆膜坚韧具有优异的附着力、柔韧性、耐磨性和抗冲击等物理性能 . 具有优异的耐碱性 . 具有良好的耐水性和耐盐水性能 . 具有优良的耐油性和抗化学药品性能 . 具有优良的耐久性和腐蚀性能 . 耐候性略差、经长时间暴晒后，表面将会发生轻微粉化，影响外观；但对保护作用影响不大用 涂 用于环

30、氧富锌底漆及环氧云铁防锈漆中间层上作为保护钢铁结构的高性能涂料配套的面漆，与碱性气体接触的钢铁结构，钢筋混凝土表面和水槽，石油贮罐浮顶等处作高性能保护涂料之用。外观和施工参数产品编码外观体积固化份* %干膜厚度m湿膜厚度m理论用量g/09-31铁红553509112209-65淡灰553509112209-67中黄553509112209-84深灰553509112209-110淡海蓝5535091122*体积固体份（按GB/T9272 eqv ISO3233:1998 规定测定）（混合后）配比 甲组份：乙组份=5：1（重量比）闪电 甲组份 27 乙组份 27干燥时间 （25）表干8h实干24

31、h完全固化 7d熟化时间（混合比）（20） 30min适用期（混合后）（20） 8h(气温大于30以上时，甲乙组份混合后适用期随着气温的升高而缩短) 复涂间隔时间湿度52030最短48h24h16h最长14d7d5d建议涂装道数 喷涂2道，干膜厚度100m，刷涂或滚涂需涂装3道。前道配套用漆 H06-4环氧富锌防锈漆为底漆、842环氧云铁防锈漆为中间层漆，或其他双组份环氧防锈漆。表面处理 . 前道漆应完全干燥 . 除尽漆膜上所有的油污和杂物施工条件 . 底材温度须高于露点以上3 . 在温度低于5时，环氧与固化剂的反应停止，不宜进行室外施工。如必须在不符合这一条件下继续进行施工时，则应在室内或支

32、帐篷、加热表面或用热空气强制通风干燥的办法予以解决 .相对湿度不大于85%涂装方法 无气喷涂 稀释剂 103稀释剂 稀释量 0-5%（以油漆重量计算） 喷嘴口径 0.4-0.5mm 喷出压力 10-30MPa（约150-300kg/c）空气喷涂 稀释剂 103稀释剂 稀释量 0-5%（以油漆重量计） 喷嘴口径 2.0-2.5mm 空气压力 0.3-0.5MPa（约3-5 kg/c）滚涂/刷涂 稀释剂 103稀释剂 稀释量 0-3%（以油漆重量计）清洗剂 103稀释剂安全措施 参见上海开林造漆厂产品安全技术说明书（简称MSDS）包装 甲组份 20L 桶装 17kg 乙组份 4L 桶装 3.4kg

33、保质期 12个月备注 为正确使用本厂的产品，请仔细阅读本说明书中的使用指南声明 以上本产品的资料及数据是根据我们的试验和实际使用中的经验而积累的，可作为施工指南。对于在我们不了解的情况下进行的施工，我们只保证油漆本身的质量，其它方面的问题恕不负责。对本说明书，我们将根据产品的不断改进有权进行修改。Colored epoxy finishQ / GHTD 85(finish coating)GENERIC TYPEComposed of epoxy resin, polyamide curing agent, titanium dioxide, coloring pigments, extend

34、er pigments, additives and solvents consisting of two component epoxy paint.GENERAL PROPERTIES high solids content, can be made thick epoxy topcoat .Tough film with excellent adhesion, flexibility, abrasion resistance and impact resistance and other physical properties That has excellent alkali resi

35、stance Has good water resistance and salt water resistance With excellent oil resistance and chemical resistance With excellent durability and corrosion resistance Weathering slightly worse, after prolonged exposure, the surface will occur slightly chalking, affecting the appearance; but has little

36、effect on the protective effectTypical uses For epoxy zinc rich primer coated and epoxy micaceous iron rust intermediate layer as a protective coating of steel structure supporting high-performance paint, alkaline gas in contact with the steel structure, reinforced concrete surface and sink, oil flo

37、ating roof storage tanks, etc. for high performance protective coatings purposes.Appearance and construction parameters产品编码Product Code外观Exterior体积固化份Volume curing parts* %干膜厚度Dry film thicknessm湿膜厚度Wet film thicknessm理论用量Theoretical amountg/09-31铁红Iron oxide red553509112209-65淡灰Light gray5535091122

38、09-67中黄In yellow553509112209-84深灰Dark gray553509112209-110淡海蓝Pale sea blue5535091122 Volume solid (according to GB/T9272 eqv ISO3233:1998 rules determine) after (mixed)The ratio component A: component B = 5:1 (weight)Flash point component A 27 Component B 27 The drying time (25 )Touch8hHandel24hFina

39、l cured 7d Curing time (mixing ratio) (20 ) for 30 minPot time (mixed) after 8 h (20 )(when the temperature is higher than 30 , a component b blend to apply with the increase of temperature and shorten)Applied time interval湿度Humidity5 20 30最少shortest48 h24 h16 h最长longest14 d7 d5 dRecommend layers 2

40、layers, dry film thickness 100m, brush or roller coating 3 layersFront-matching paint H06-4 Epoxy zinc rich rust as primer, 842 epoxy micaceous iron rust paint for the middle layer, or other two-component epoxy anti-rust paint .Surface treatment should be completely dry before the Road. Divisible fi

41、lm all the oil and debrisConstruction conditions Substrate temperature 3 above the dew pointAt temperatures below 5 , epoxy and curing agent reaction was stopped, not for outdoor construction . If this does not meet the conditions must be continued under construction, should be indoors or in a tent, with hot air heating surface or forced air drying to be addressedRelative humidity less than 85%Coating methodsAirless Spray Thinner 103 ThinnerDilute the amount of 0-5% ( by weight of paint )Nozzle diameter 0.4-0.5mmDischarge pressure 10-30MPa ( approximately 150-300kg / c )Air Spray