《汽车转向系统外文原文及翻译(共15页).docx》由会员分享，可在线阅读，更多相关《汽车转向系统外文原文及翻译(共15页).docx（15页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、精选优质文档-倾情为你奉上本文摘于Race Car Vehicle Dynamics 作者：William F. Miliken and Douglas L. MilikenSteering systemsIntroduction This chapter begins with a discussion of steering geometrycaster angle ,trail ,kingpin inclination ,and scrub radius .The next section discuss Ackermann geometry followed by steering r
2、acks and gears .Ride steer (bump steer ) and roll steer are closely related to each other ;without compliance they would be the same .Finally ,wheel alignment is discussed .this chapter is tied to chapter 17 on suspension geometry when designing a new chassis ,steering and suspension geometry consid
3、erations are high priorities . steering geometry The kingpin in a solid front axle is the steering pivot .In modern independent suspensions , introduced by Maurice olley at Cadillac in 1932,the kingpin is replaced by two (or more ) ball joints that define the steering axis .This axis is not vertical
4、 or centered on the tire contact patch for a number of reason .see figure to clarify how kingpin location is measured .In front view ,the angle is called kingpin inclination and the offset of the steering axis from the center of the tire print measured along the ground is called scrub (or scrub radi
5、us ). The distance from the kingpin axis to the wheel center plane , measured horizontally at axle height ,is the spindle length .In side view the kingpin angle is called caster angle ; if the kingpin axis does not pass through the wheel center then side view kingpin offset is present ,as in most mo
6、torcycle front ends .The distance measured on the ground from the steering axis to the center of the tire print is the trail (called caster offset in ref .1 )Kingpin front view geometry As mentioned in chapter 17, kingpin inclination ,spindle length ,and scrub are usually a compromise between packag
7、ing and performance requirements .Some factors to consider include : a positive spindle length (virtually every car is positive as shown in figure the car will be raised up as the wheels are steered away from center .The more the kingpin inclination is tilted from vertical the more the car will be r
8、aised when the front wheels are steered .This effect always raises the car , regardless of which direction the wheel is steered ,unless the kingpin inclination is true vertical .the effect is symmetric side to side only if there is no caster angle .See the following section on caster angle .For a gi
9、ven kingpin inclination ,a longer positive spindle length will increase the amount of lift with steer . effect of kingpin inclination and spindle length in raising the front end ,by itself ,is to aid centering of the steering at low speed .At high speed any trail will probably swamp out the effect t
10、hat raise ad fall have on centering .3. Kingpin inclination affects the steer camber characteristic .when a wheel is steered ,it will lean out at the top ,toward positive camber ,if the kingpin is inclined in the normal direction (toward the center of the car at the upper end ). Positive camber resu
11、lts for both left and right-hand steer .the amount of this effect is small ,but significant if the track includes tight turns.4. When a wheel is rolling over a bumpy road ,the rolling radius is constantly changing ,resulting in changes of wheel rotation speed . This gives rise to longitudinal forces
12、 at the wheel center .The reaction of these forces will introduce kickback into the steering in proportion to the spindle length .If the spindle length is zero then there will be no kick from this source .Design changes made in the last model of the GM “P ”car (fiero ) shortened the spindle length a
13、nd this resulted in less wheel kickback on rough roads when compared to early model “P ”cars.5. The scrub radius shown in figure is negative ,as used on front-wheel drive cars (see below ) . driving or braking forces (at the ground ) introduce steer torques proportional to the scrub radius . If the
14、driving or braking force is different on left and right wheels then there will be a net steering torque felt by the driver (assuming that the steering gear has good enough rev erse efficiency ).The only time that this is not true is with zero scrub (centerpoint steering ) because there is no moment
15、arm for the drive (or brake ) force to generate torque about the kingpin .With very wide tires the tire forces often are not centered in the wheel center plane due to slight changes in camber ,road surface irregularities ,tire nonuniformity (conicity ),or other asymmetric effects .These asymmetries
16、can cause steering kickback regardless of the front view geometry .Packaging requirements often conflict with centerpoint steering and many race cars operate more or less okay on smooth tracks with large amounts of scrub .6. For front drive ,a negative scrub radius has two strong stabilizing effects
17、 :first ,fixed steering wheel if one drive wheel loses traction ,the opposing wheel will toe out an amount determined by the steer compliance in the system .This will tend to steer the car in a straight line ,even though the tractive force is not equal side-to side and the unequal tractive force is
18、applying a yaw moment to the vehicle .Second ,with good reverse efficiency the drivers hands never truly fix the steering wheel . In this case the steering wheel may be turned by the effect of uneven longitudinal tractive forces ,increasing the stabilizing effect of the negative scrub radius .Under
19、braking the same is true .Negative scrub radius tends to keep the car traveling straight even when the braking force is not equal on the left and right side front tiresome (due to differences in the roadway or the brakes).Caster angle and trail With mechanical trail ,shown in figure ,the tire print
20、follows behind the steering axis in side view .Perhaps the simplest example is on an office chair caster with any distance of travel ,the wheel aligns itself behind the point .More trail means that the tire side force has a large moment arm to act on the kingpin axis .This produces more self-centeri
21、ng effect and is the primary source of self-centering moment about the kingpin axis at speed .Some considerations for choosing the caster angle and trail are : trail will give higher steering force .with all cars ,less trail will lower the steering force .In some cases ,manual steering can be used o
22、n heavy sedans (instead of power steering ) if the trail is reduced to almost zero . angle ,like kingpin inclination ,cause the wheel to rise and fall with steer .unlike kingpin inclination ,the effect is opposite from side to side .With symmetric geometry (including equal positive caster on left an
23、d right wheels ) ,the effect of left steer is to roll the car to the right ,causing a diagonal weight shift .In this case ,more load will be carried on the LF RR diagonal ,an oversteer effect in a left-hand turn .The diagonal weight shift will be larger if stiffer springing is used because this is a
24、 geometric effect .The distance each wheel rises (or falls ) is constant but the weight jacking and chassis roll angle are functions of the front and rear roll stiffness. This diagonal load change can be measured with the car on scales and alignment ( weaver ) plates .Keep in mind that the front whe
25、els are not steered very much in actual racing , except on the very tightest hairpin turns . For example , on a 100-ft .radius (a 40-50 mph turn ), a 10-ft. wheelbase neutral steer car needs only about .of steer at the front wheels (with a 16:1steering ratio this is about 90degree at the steering wh
26、eel ).For cars that turn in one direction only , caster stagger (differences in left and right caster ) is used to cause the car to pull to one side due to the car seeking the lowest ride height . caster stagger will also affect the diagonal weight jacking effect mentioned above . If the caster is o
27、pposite (positive on one side and negative the same number of degrees on the other side ) then the front of the car will only rise and fall with steer , no diagonal weight jacking will occur .3. Caster angle affects steer-camber but ,unlike kingpin inclination ,the effect is favorable . With positiv
28、e caster angle the outside wheel will camber in a negative direction (top of the wheel toward the center of the car ) while the inside wheel cambers in a positive direction , again learning into the turn .In skid recovery , “opposite lock ” (steer out of the turn ) is used and in this case the steer
29、camber resulting from caster angle is in the “wrong ” direction for increased front tire grip . conveniently ,this condition results from very low lateral force at the rear so large amounts of front grip are not needed .4. As discussed in chapter 2, tires have pneumatic trail which effectively adds
30、to (and at high slip Angles subtracts from ) the mechanical trail . This tire effect is nonlinear with lateral force and affects steering torque and driver feel .In particular , the fact that pneumatic trail approaches zero as the tire reaches the limit will result in lowering the self-centering tor
31、que and can be s signal to the driver that the tire is near breakaway .The pneumatic trail “breakaway signal” will be swamped out by mechanical trail if the mechanical trail is large compared to the pneumatic trail . the trail is measured in a direction perpendicular to the steering axis (rather tha
32、n horizontal as shown in figure because this more accurately describes the lever (moment ) arm that connects the tire lateral forces to the kingpin .Tie rod location Note that in figure a shaded area is shown for the steering tie rod location . Camber compliance under lateral force is unavoidable an
33、d if the tie rod is located as noted ,the effect on the steering will be in the understeer ( steer out of the turn ) direction becomes much more complex than can be covered here . Ackerman steering geometry As the front wheels of a vehicle are steered away from the straight-ahead position ,the desig
34、n of the steering linkage will determine if the wheels stay parallel or if one wheel steers more than the other .This difference in steer Angles on the left and right wheels should not be confused with toe-in or toe-out which are adjustments and add to ( or subtract from ) Ackerman geometric effects
35、 .For low lateral acceleration usage (street cars) it is common to use Ackerman geometry . as seen on the left of figure , this geometry ensures that all the wheels roll freely with no slip Angles because the wheels are steered to track a common turn center . Note that at low speed all wheels are on
36、 a significantly different radius , the inside front wheel must steer more than the outer front wheel . A reasonable approximation to this geometry may be as shown in figure .According to ref .99, Rudolf Ackerman patented the double pivot steering system in 1817 and in 1878, Charles Jeantaud added t
37、he concept mentioned above to eliminate wheel scrubbing when cornering . Another reason for Ackermann geometry ,mentioned by Maurice olley , was to keep carriage wheels from upsetting smooth gravel driveways .High lateral accelerations change the picture considerably . Now the tires all operate at s
38、ignificant slip Angles and the loads on the inside track are less than on the outside track . Looking back to the tire performance curves ,it is seen that less slip angle is required at lighter loads to reach the peak of the cornering force to a higher slip angle than required for maximum side force
39、 . Dragging the inside tire along at high slip Angles ( above for peak lateral force ) raise the tire temperature and slows the car down due to slip angle ( induced ) drag .For racing , it is common to use parallel steering or even reverse Ackermann as shown on the center and right side of figure .I
40、t is possible to calculate the correct amount of reverse Ackermann if the tire properties and loads are known . In most cases the resulting geometry is found to be too extreme because the car must also be driven (or pushed ) at low speeds , for example in the pits .Another point to remember is that
41、most turns in racing have a fairly large radius and the Ackermann effect is very small . In fact , unless the steering system and suspension are very stiff ,compliance (deflection ) under cornering loads may steer the wheels more than any Ackermann (or reverse Ackermann ) built into the geometry .Th
42、e simplest construction that generates Ackermannn geometry is shown in figure for “rear steer ” . Here ,the rack (cross link or relay rod in steering box systems ) is located behind the front axle and lines staring at the kingpin axis , extended through the outer tie rod ends , intersect in the cent
43、er of the rear axle . The angularity of the steering knuckle will cause the inner wheel to steer more than the outer (toe-out on turning ) and a good approximation of “perfect Ackermann ” will be achieved . The second way to design-in differences between inner and outer steer Angles is by moving the
44、 rack (or cross link ) forward or backward so that it is no longer on a line directly connecting the two outer tie rod ball joints .This is shown in figure . with “rear steer ” , as shown in the figure ,moving the rack forward will tend more toward parallel steer (and eventually reverse Ackermann ),
45、 and moving it toward the rear of the car will increase the toe-out on turning .A third way to generate toe with steering is simply to make the steering arms different lengths . A shorter steering arm (as measured from the kingpin axis to the outer tie rod end ) will be steered through a larger angl
46、e than one with a longer knuckle. Of course this effect is asymmetric and applies only to cars turning in one directionoval track cars .Recommendation With the conflicting requirements mentioned above , the authors feel that parallel steer or a bit of reverse Ackermann is a reasonable compromise . W
47、ith parallel steer , the car will be somewhat difficult to push through the pits because the front wheels will be fighting each other . at racing speeds , on large-radius turns , the front wheels are steered very little , thus any ackermann effects will not have a large effect on the individual whee
48、l slip angles , relative to a reference steer angle , measured at the centerline of the car . 文献翻译 摘自Race Car Vehicle Dynamics第19章 转向系统序言：本章以转向几何参数的讨论为开始，包括主销后倾角，后倾拖距，主销内倾角，主销偏置量。接下来的部分讨论了转向齿轮齿条以及阿克曼转向几何关系。跳动转向和侧倾转向之间是紧密相关的，如果没有柔性这两种情况是等同的。最后讨论了车轮的调整。这一章与第17章的悬架几何形状密切相关，在设计新的底盘系统时，转向和悬架几何参数是优先考虑的因素。
49、 转向几何关系（定位参数） 在整体式车桥上转向节主销是转向时的枢轴。1932年Maurice Olley在Cadillac首次提出了现在的非独立悬架，主销因此而被两个球绞连接定义的转向轴线代替。因为各种原因这根轴并不是垂直的也不在轮胎接地中心处。主销的位置表示见图。在前视图中，主销偏转的角度被称为主销内倾角，转向主销与地面的交点至车轮中心平面与地面相交处的距离称之为主销偏置量。在前轴所在水平面内，从主销轴心到车轮中心平面的距离称为主销偏距（spindle length）。在侧视图中，主销偏转角度称为主销后倾角。如果主销轴线没有通过车轮中心那么就有了侧视的主销偏距（side view kingpin offset），就像大部分的摩托车前轮一样。在地平面内测量从主销到轮胎接地点中心的距离称为主销后倾拖距。前视图中的主销定位参数正如在17章中提到，主销内倾角，主销偏距还有主销偏置量在装配以及性能满足时往往是互相妥协