《齿轮参数-中英文对照(共6页).docx》由会员分享，可在线阅读，更多相关《齿轮参数-中英文对照(共6页).docx（6页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、精选优质文档-倾情为你奉上EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data（制造参数）part number（零件号）tooth form（齿面）gear type（齿轮类型）number of teeth（齿数）normal module（法向模数）normal pressure angle (at ref circle)法向压力角（在分度圆上）helix angle (at ref circle)螺旋角（在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）o
2、utside diameter（齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter（分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness (at reference circle)法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根
3、圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中
4、凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash (nominal CD ,ROOM TEMP)侧隙(法线方向，室温) general notes(通用技术要求)1.DO not scale drawin
5、g(不要在图上量取尺寸)2.all surfaces corners and edges must be free from burrs and sharp edges-break 0.075 MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm)3.unless otherwise stated(除非特别注明,否则) A.all dimensions and tolerance are in millimeters per Chinese standard(所有以毫米为单位的尺寸和公差均按中国标准) B.all surface finishes to be 3.2 micro
6、meter or better(所有表面粗糙度不应低于3.2) C.all dimension are finished dimensions;no allowance has been made for any change in maximum or least material condition due to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差) D linear dimensions to be +/- 0.25 MM(线性尺寸偏差为+/- 0.25 MM) E angular dimensions to be +/-
7、 0.5(角度尺寸偏差为+/- 0.5)4.mark part number as shown(如图作零件号)5.mark serial number as shown(如图作系列号)6.heat treatment to be applied to all surfaces(整体热处理)gear notes(齿轮技术要求)1.do not grind roots and fillets after heat treatment(热处理后不得磨及齿根和圆角)2.no steps or grooves permissible in root and fillet region after hon
8、ing or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)3.profile tolerance based upon floating band fit(齿形误差应以公差带为计)4.gear must be free from grind burns and tempering(齿面不得烧伤)5.pitch line runout and other tooth tolerances are with respect to datum A(节圆跳动和其它齿轮公差均以基准A为测量基准)6.profile tolerance to be measured between form
9、 and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)7.min hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)8.root radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆直径。9.do not thru harden tooth tips(齿尖不得淬透)专心-专注-专业齿轮基本术语齿轮 Toothed gear；Gear 齿面 Tooth
10、 flank 长幅内摆线 Prolate hypocycloid齿轮副 Gear pair 右侧齿面 Right flank 短幅内摆线 Curtate hypocycloid平行轴齿轮副 Gear pair with parallel axes 左侧齿面 Left flank 渐开线 Involute；Involute to a circle相交轴齿轮副 Gear pair with intersecting axes 同侧齿面 Corresponding flank 延伸渐开线 Prolate involute齿轮系 Train of gears 异侧齿面 Opposite flank 缩
11、短渐开线 Curtate involute行星齿轮系 Planetary gear train 工作齿面 Working flank 球面渐开线 Spherical involute齿轮传动 Gear drive；Gear transmission 非工作齿面 Non-working flank 渐开螺旋面 Involute helicoid配对齿轮 Mating gears 相啮齿面 Mating flank 阿基米德螺旋面 Screw helicoid小齿轮 Pinion 共轭齿面 Conjugate flank 球面渐开螺旋面 Spherical involute helicoid大齿轮
12、 Wheel；Gear 可用齿面 Usable flank 圆环面 Toroid主动齿轮 Driving gear 有效齿面 Active flank 圆环面的母圈 Generant of the toroit从动齿轮 Driven gear 上齿面 Addendum flank 圆环面的中性圈 Middle circle of the toroid行星齿轮 Planet gear 下齿面 Dedendum flank 圆环面的中间平面 Middle-plane of the toroid行星架 Planet carrier 齿根过渡曲面 Fillet 圆环面的内圈 Inner circle
13、of the toroid太阳轮 Sun gear 齿顶 Crest；Top land 啮合干涉 Meshing interference内齿圈 Ring gear；Annulus gear 槽底 Bottom land 切齿干涉 Cutter interference外齿轮 External gear 齿廓 Tooth profile 齿廓修型 Profile modification；Profile correction内齿轮 Internal gear 端面齿廓 Transverse profile 修缘 Tip relief中心距 Centre distance 法向齿廓 Normal
14、 profile 修根 Root relief轴交角 Shaft angle 轴向齿廓 Axial profile 齿向修形 Axial modification；Longitudinal correction连心线 Line of centres 背锥齿廓 Back cone tooth profile 齿端修薄 End relief减速齿轮副 Speed reducing gear pair 齿线 Tooth trace 鼓形修整 Crowning增速齿轮副 Speed increasing gear pair 齿棱 Tip；Tooth tip 鼓形齿 Crowned teeth齿数比 G
15、ear ratio 模数 Module 挖根 Undercut传动比 Transmission ratio 端面模数 Transverse module 瞬时轴 Instantaneous axis轴平面 Axial plane 法向模数 Normal module 瞬时接触点 Point of contact基准平面 Datum plane 轴向模数 Axial module 瞬时接触线 Line of contact节平面 Pitch plane 径节 Diametral pitch 端面啮合线 Transverse path of contact端平面 Transverse plane
16、齿数 Number of teeth 啮合曲面 Surface of action法平面 Normal plane 当量齿数 Virtual number of teeth 啮合平面 Plane of action分度曲面 Reference surface 头数 Number of starts；Number of threads 啮合区域 Zone of action节曲面 Pitch surface 螺旋线 Helix；Circular helix 总作用弧 Total arc of transmission齿顶曲面 Tip surface 圆锥螺旋线 Conical spiral 端面
17、作用弧 Transverse arc of transmission齿根曲面 Root surface 螺旋角 Helix angle；Spiral angle 纵向作用弧 Overlap arc基本齿廓 Basic tooth profile 导程 Lead 总作用角 Total angle of transmission基本齿条 Basic rack 导程角 Lead angle 端面作用角 Transverse angle of transmission产形齿条 Counterpart rack 阿基米德螺旋线 Archimedes spiral 纵向作用角 Overlap angle产
18、形齿轮 Generating gear of a gear 外摆线 Epicycloid 总重合度 Total contact ratio产形齿面 Generating flank 长幅外摆线 Prolate epoicycloid 端面重合度 Transverse ratio基准线 Datum line 短幅外摆线 Curtate epoicycloid 纵向重合度 Overlap ratio轮齿 Gear teeth；Tooth 摆线 Cycloid 标准齿轮 Standard gears齿槽 Tooth space 长幅摆线 Prolate cycloid 非变位齿轮 X-gero ge
19、ar右旋齿 Right-hand teeth 短幅摆线 Curtate cycloid 标准中心距 Referencr centre distance左旋齿 Left-hand teeth 内摆线 Hypocycloid 名义中心距 Nominal centre distance变位齿轮 Gears with addendum modification；X-gears 直齿轮 Spur gear 分度圆柱面 Reference cylinder高度变位圆柱齿轮副 X-gear pair with reference centre distance 斜齿轮 Helical gear；Single
20、-helical gear 节圆柱面 Pitch cylinder角度变位圆柱齿轮副 X-gear pair with modified centre distance 直齿条 Spur rack 基圆柱面 Basic cylinder高度变位锥齿轮副 X-gear pair without shaft angle modification 斜齿条 Helical rack 齿顶圆柱面 Tip cylinder角度变位圆柱齿轮副 X-gear pair with shaft angle modification 人字齿轮 Double-helical gear 齿根圆柱面 Root cylin
21、der变位系数 Modification coefficient 渐开线齿轮 Involute cylindrical gear 节点 Pitch point变位量 Addendum modification 摆线齿轮 Cycloidal gear 节线 Pitch line径向变位系数 Addendum modification coefficient 圆弧齿轮 Circular-arc gear；W-N gear 分度圆 Reference circle中心距变位系数 Centre distance modification coefficient 双圆弧齿轮 Double-circula
22、r-arc gear 节圆 Pitch circle圆柱齿轮 Cylindrical gear 假想曲面 Imaginary surfance 基圆 Basic circle顶圆 Tip circle 任意点法向压力角 Normal pressure angle at a point 定位面 Locating face根圆 Root circle 任意点端面压力角 Transverse pressure angle at a point 外锥距 Outer cone distance齿距 Pitch 啮合角 Working pressure angle 内锥距 Inner cone dista
23、nce齿距角 Angular pitch 顶隙 Bottom clearance 中点锥距 Mean cone distance公法线长度 Base tangent length 圆周侧隙 Circumferential blacklash 背锥距 Back cone distance分度圆直径 Reference diameter 法向侧隙 Normal blacklash 安装距 Locating distance节圆直径 Pitch diameter 径向侧隙 Radial blacklash 轮冠距 Tip distance；crown to back基圆直径 Base diamete
24、r 锥齿轮 Bevel gear 冠顶距 Apex to crown顶圆直径 Tip diameter 锥齿轮副 Bevel gear pair 偏置距 Offset根圆直径 Root diameter 准双曲面齿轮副 Hypoid gear pair 齿线偏移量 Offset of tooth trace齿根圆角半径 Fillet radius 准双曲面齿轮 Hypoid gear 分锥角 Reference cone angle齿高 Tooth depth 冠轮 Crown gear 节锥角 Pitch cone angle工作高度 Working depth 端面齿轮 Contrate
25、gear 顶锥角 Tip angle齿顶高 Addendum 直齿锥齿轮 Straight bevel gear 根锥角 Root angle齿根高 Dedendum 斜齿锥齿轮 Skew bevel gear；Helical bevel gear 背锥角 Back cone angle弦齿高 Chordal height 曲面齿锥齿轮 Curved tooth bevel gear 齿顶角 Addendum angel固定弦齿高 Constant chord height 弧齿锥齿轮 Spiral bevel gear 齿根角 Dedendum angle齿宽 Facewidth 摆线齿锥齿
26、轮 Enicycloid bevel gear 任意点压力角 Pressure angle at a point有效齿宽 Effective facewidth 零度齿锥齿轮 Zero T bevel gear 任意点螺旋角 Spiral angle at a point端面齿厚 Transverse tooth thickness 圆柱齿轮端面齿轮副 Contrate gear pair 中点螺旋角 Mean spiral angle法向齿厚 Normal tooth thickness 锥齿轮的当量圆柱齿轮 Virtual cylindrical gear of bevel gear 大端
27、螺旋角 Outer spiral angle端面基圆齿厚 Transverse base thickness 8字啮合锥齿轮 Octoid gear 小端螺旋角 Inner spiral angle法向基圆齿厚 Normal base thickness 圆柱齿弧锥齿轮 Spiral bevel gear with circle arc tooth profile 蜗杆 Worm端面弦齿厚 Transverse chordal tooth thickness 分度圆锥面 Reference cone 蜗轮 Worm wheel固定弦齿厚 Constant chord 节圆锥面 Pitch co
28、ne 蜗杆副 Worm gear pair端面齿顶厚 Crest width 齿顶圆锥面 Face cone；tip cone 圆柱蜗杆 Cylindrical worm法向齿顶厚 Normal crest width 齿根圆锥面 Root cone 圆柱蜗杆副 Cylindrical worm pair端面齿槽宽 Transverse spacewidth 背锥面 Back cone 环面蜗杆 Enveloping worm法向齿槽宽 Normal spacewidth 前锥面 Front cone 环面蜗杆副 Enveloping worm pair齿厚半角 Tooth thickness
29、 half angle 中锥面 Middle cone 阿基米德蜗杆 Straight sided axial worm；ZA-worm槽宽半角 Spacewidth half angle 分锥顶点 Reference cone apex 渐开线蜗杆 Involute helicoid worm；压力角 Pressure angle 轴线交点 Crossing point of axes 法向直廓蜗杆 Straight sided normal worm；齿形角 Nominal pressure angle 齿根圆环面 Root tosoid 椭圆齿轮 Elliptical gear 咽喉面
30、Gorge 非圆齿轮副 Non-circular gear pair平面蜗杆 Planar worm wheel；P-worm wheel 喉平面 Gorge plane 圆柱针轮副 Cylindsical lantern pinion and wheel平面包络环面蜗杆 Planar double enveloping worm；TP-worm 喉圆 Gorge circle 针轮 Cylindsical tan tein gear ；pin-wheel平面二次包络蜗杆 Planar double-enveloping worm wheel；TP-worm wheel 分度圆蜗旋线 Refe
31、rence helix 谐波齿轮副 Harmoric gear drive锥面包络环面蜗杆 Toroid enveloping worm wheel；TK-worm wheel 螺纹 Thread 波发生器 Wave generator 蜗杆齿宽 Worm facewidth 柔性齿轮 Flexspine锥蜗杆 Spiroid 蜗轮齿宽 Worm wheel facewidth 刚性齿轮 Circular spline锥蜗轮 Spiroid gear 直径系数 Diametral quotient 非圆齿轮 Non-circular gear锥蜗杆副 Spiroid gear pair 咽喉半径 Gorge radius 分度圆环面 Reference tosoid中平面 Mid-plane 齿宽角 Width angle