《冲压模具专业英语(共42页).doc》由会员分享，可在线阅读，更多相关《冲压模具专业英语(共42页).doc（42页珍藏版）》请在taowenge.com淘文阁网|工程机械CAD图纸|机械工程制图|CAD装配图下载|SolidWorks_CaTia_CAD_UG_PROE_设计图分享下载上搜索。
1、精选优质文档-倾情为你奉上冲压模具专业术语英汉对照目录一， 模具厂常用之标准零配件二， 模具钢材三， 组装、冲压、喷漆等专业词汇四， 模具工程常用词汇五， 模具零件类六， 品质人员名称类七， 系统文件类八， 模具技术用语九， 各式模具分类用语十， 模具常用之工作机械设备十一，表面处理关连用语十二，成形不良用语十三，各种冲模加工关连用语十四，模具常用刀具与工作法用语十五，冲压机械及周边关连用语十六，线切割放电加工关连用语十七，模具加工方法十八，机械设计及周边其他用语一，模具厂常用之标准零配件 air vent vale 通气阀 anchor pin 锚梢 angular pin 角梢 baffl
2、e 调节阻板 angular pin 倾斜梢 baffle plate 折流档板 ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑块 binder plate 压板 blank holder 防皱压板 blanking die 落料冲头 bolster 上下模板 bottom board 浇注底板 bolster 垫板 bottom plate 下固定板 bracket 托架 bumper block 缓冲块 buster 堵口 casting ladle 浇注包 casting lug 铸耳 cavity 模穴(模仁) cavity reta
3、iner plate 模穴托板 center pin 中心梢 clamping block 锁定块 coil spring 螺旋弹簧 cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓 core 心型 core pin 心型梢 cotter 开口梢 cross 十字接头 cushion pin 缓冲梢 diaphragm gate 盘形浇口 die approach 模头料道 die bed 型底 die block 块形模体 die body 铸模座 die bush 合模衬套 die button 冲模母模 die clamper 夹模器 die fast
4、ener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 冲模板 die set 冲压模座 direct gate 直接浇口 dog chuck 爪牙夹头 dowel 定位梢 dowel hole 导套孔 dowel pin 合模梢 dozzle 辅助浇口 dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套 ejector
5、 pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘? flash gate 毛边形浇口 flask 上箱 floating pun
6、ch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧? goose neck 鹅颈管 guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶?冲头 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒 hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头
7、 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢衬套 knockout bar 脱模杵 land 合模平坦面 land area 合模面 leader busher 导梢衬套 lifting pin 起模顶? lining 内衬 locating center punch 定位中心冲头 locating pilot pin 定位导梢 locating ring 定位环 lock block 压块 locking block 定位块 locking plate 定位板 loose bush 活动衬套 making die 打印冲子 m
8、anifold block 歧管档块 master plate 靠模样板 match plate 分型板 mold base 塑胶模座 mold clamp 铸模紧固夹 mold platen 模用板 moving bolster 换模保持装置 moving bolster plate 可动侧模板 one piece casting 整体铸件 parallel block 平行垫块 paring line 分模线 parting lock set 合模定位器 pass guide 穴型导板 peened head punch 镶入式冲头 pilot pin 导? pin gate 针尖浇口 p
9、late 衬板 pre extrusion punch 顶挤冲头 punch 冲头 puncher 推杆 pusher pin 衬套梢 rack 机架 rapping rod 起模杆 re-entrant mold 凹入模 retainer pin 嵌件梢 retainer plate 托料板 return pin 回位梢 riding stripper 浮动脱模器 ring gate 环型浇口 roller 滚筒 runner 流道 runner ejector set 流道顶出器 runner lock pin 流道拉梢 screw plug 头塞 set screw 固定螺丝 shedd
10、er 脱模装置 shim 分隔片 shoe 模座之上下模板 shoot 流道 shoulder bolt 肩部螺丝 skeleton 骨架 slag riser 冒渣口 slide(slide core) 滑块 slip joint 滑配接头 spacer block 间隔块 spacer ring 间隔环 spider 模蕊支架 spindle 主轴 sprue 注道 sprue bushing 注道衬套 sprue bushing guide 注道导套 sprue lock bushing 注道定位衬套 sprue puller 注道拉料? spue line 合模线 square key
11、 方键 square nut 方螺帽 square thread 方螺纹 stop collar 限位套 stop pin 止动梢 stop ring 止动环 stopper 定位停止梢 straight pin 圆柱? stripper bolt 脱料螺栓 stripper bushing 脱模衬套 stripper plate 剥料板 stroke end block 行程止梢 submarine gate 潜入式浇口 support pillar 支撑支柱/顶出支柱 support pin 支撑梢 supporting plate 托板 sweep templete 造模刮板 tab g
12、ate 辅助浇口 taper key 推拔键 taper pin 拔锥梢/锥形梢 teeming 浇注 three start screw 三条螺纹 thrust pin 推力销 tie bar 拉杵 tunnel gate 隧道形浇口 vent 通气孔 wortle plate 拉丝模板 二，模具钢材 alloy tool steel 合金工具钢 aluminium alloy 铝合金钢 bearing alloy 轴承合金 blister steel 浸碳钢 bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢 clad sheet 被
13、覆板 clod work die steel 冷锻模用钢 emery 金钢砂 ferrostatic pressure 钢铁水静压力 forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板 hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢 hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢 low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢 martrix alloy 马特里斯合
14、金 meehanite cast iron 米汉纳铸钢 meehanite metal 米汉纳铁 merchant iron 市售钢材 molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢 nickel chromium steel 镍铬钢 prehardened steel 顶硬钢 silicon steel sheet 矽钢板 stainless steel 不锈钢 tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜 troostite 吐粒散铁 tungsten steel ?钢 vin
15、yl tapped steel sheet 塑胶覆面钢板 三，组装、冲压、喷漆等专业词汇Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse toge
16、ther熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电
17、源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straighte
18、ner整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |plein?|刨床 miller铣床 grinder磨床 driller铣床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长
19、 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect
20、material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |skr?pid|报废 scrape .v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation | ksidei?n|氧化 scratch刮伤 de
21、nts压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=p
22、late pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压
23、板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾
24、袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard
25、不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 paintin
26、g peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交
27、货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 def
28、ective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stret
29、ch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, ma
30、ke preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch-to throw-over switc
31、hing over切换 engineering, project difficulty 工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feede
32、r送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw hole
33、s抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安
34、全库存 acceptance = receive验收 to notice通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tig
35、ht a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 四，模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 pan
36、el board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate
37、, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder文件夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count
38、复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summ
39、ary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部(NHK厂区送财会部) Application status records of year-end physical inventory List and ph
40、ysical inventory card 年终盘点卡与清册使用状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minut
41、es会议记录 meeting type 会别 distribution department分发单位 location地点 chairman主席 present members出席人员 subject主题 conclusion结论 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺 wo
42、rk order工令 revision版次 remark备注 production control confirmation生产确认 checked by初审 approved by核准 department部门 stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用 obsolete material良品已呆滞 to be inspected or reworked 待验或重工 total合计 cause description原因说明 part number/ P/N 料号 type形态
43、item/group/class类别 quality品质 prepared by制表 notes说明 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing materials包材
44、good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet
45、stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert异形
46、子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalid
47、ipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条码 flow chart流程表单 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fu